background image

QUICK START GUIDE

u-line.com

QUICK START GUIDE

7

u-line.com

 

3. Remove door by tilting forward and lifting door off 

bottom hinge. Retain shoulder washers; they will be 
reused.

4. Remove four screws from hinge holes on the opposite 

side. Reinstall into holes where the hinge was 
removed. Take care not to scratch cabinet.

Remove and reinstall bottom hinge:

1. Remove bottom hinge from cabinet using a Torx T-25 

screwdriver to remove three screws.

2. Remove corresponding screws on opposite side of 

cabinet.

3. Flip hinge plate over and reinstall on opposite side.

Prepare door for reinstallation:

1. Remove gasket. This will reveal mounting holes for the 

magnet assembly

2. Remove plunger bracket from door with T-10 TORX 

driver. Be sure to only remove the two screws holding 
the assembly to the door. Reinstall on the opposite end 
of the door

3. Rotate gasket 180°, aligning notch with plunger 

bracket and pressing firmly into the gasket channel 
starting at the corners.

4. Rotate door 180° to reverse. 

Install top hinge and door:

1. Use alternate hinge supplied with unit and reinstall the 

screws. Do not tighten..

2. Lift the door on to the bottom hinge.

3. Align flat edge of the hinge with the outer edge of the 

unit.

4. Tighten three screws. 

Align and adjust the door:

Align and adjust the door (see DOOR ALIGNMENT AND 
ADJUSTMENT).

Install grille

7

Summary of Contents for U-ADA24RINT-00A


















Reviews: