background image

USER GUIDE

Cleaning

Cleaning

CLEANING VS. SANITIZING

This guide will address both the cleaning and the sanitizing 
of the unit.

Clean the unit to remove dried food and spills, to prevent 
build-up of grime, and to maintain the natural luster 
stainless steel surfaces.

Sanitize the unit when exposed to raw meat juice or 
human germs such as from a sneeze or being touched by 
someone who is ill. Sanitizing the unit can also be part of 
regular cleaning routine.

Stainless Surfaces

Stainless door panels, handles and frames can discolor 
when exposed to chlorine gas, pool chemicals, saltwater or 
cleaners with bleach.

Keep your stainless unit looking new by cleaning with a 
good quality all-in-one stainless steel cleaner and polish 
monthly. For best results use Claire

®

 Stainless Steel 

Polish and Cleaner. Comparable products are acceptable. 
Frequent cleaning will remove surface contamination that 
could lead to rust. Some installations may require cleaning 
weekly.

Do not clean with steel wool pads.
Do not use stainless steel cleaners or polishes on 
any glass surfaces.

Clean any glass surfaces with a non-chlorine glass cleaner.

Do not use cleaners not specifically intended for 
stainless steel on stainless steel surfaces (this 
includes glass, tile, and counter cleaners).

If any surface discoloring or rusting appears, clean it 
quickly with Bon-Ami

®

 or Barkeepers Friend Cleanser

®

 and 

a nonabrasive cloth. Always clean with the grain. Always 

finish with Claire

®

 Stainless Steel Polish and Cleaner or 

comparable product to prevent further problems.

Using abrasive pads such as ScotchBrite™ will
cause the graining in the stainless steel to
become blurred.

Rust not cleaned up promptly can penetrate the
surface of the stainless steel and complete
removal of the rust may not be possible.

CLEAN INTERIOR COMPONENTS

Use warm or hot water with dish soap to clean all removed 
components and interior surfaces. You may use a vinegar and 
water solution in place of soap. Proceed to sanitizing.

Note: Cleaning soaps and vinegar solutions are not 
sanitizers.

SANITIZE INTERIOR COMPONENTS AND SURFACES

Choose a Commercial Sanitizer Safe for Stainless 
Steel

•  Read the directions for proper use to ensure that the 

surface will actually be sanitized

•  Many products require rinsing with water after use, 

especially when food will be touching the surface

•  Some products require a wait time before rinsing

•  Verify the sanitizer you are using is safe for stainless 

steel.

Mix Your Own Sanitizer

      Isopropyl Alcohol (rubbing alcohol)

1.  Fill a clean, empty spray bottle with isopropyl alcohol
2.  Spray surface 
3.  Wait 20 minutes
4.  Dampen a non-abrasive cloth with isopropyl alcohol and 

wipe down surface

5.  Dry surface with a clean dry non-abrasive cloth

      Unscented Bleach and Water

1.  Create a solution of 1 tablespoon of unscented bleach 

with one gallon of water.

2.  Submerse small parts for no more than 3 minutes - rinse 

immediately and allow to air dry or dry with a disposable 
paper towel.

3.  Fill a clean, empty spray bottle with bleach solution.
4.  Spray surface.
5.  After 2-3 minutes, use clean potable water to thoroughly 

rinse off surface. Allow to air dry or dry with a disposable 

paper towel.

6.  Sanitize the door and all holes where the hinges attach to 

the unit and the brackets attach to the door as well as all 
the screws.

CLEAN EXTERIOR SURFACES

Use Bon-Ami

®

 or Barkeepers Friend Cleanser

®

 and a 

nonabrasive cloth. Always clean with the grain. Always finish 

with Claire

®

 Stainless Steel Polish and Cleaner or comparable 

product to prevent further problems.

    

20

Summary of Contents for U-ADA24RB-13B













































Reviews: