background image

U-Line 3000 Series Maintenance

6

Door Alignment and Adjustment

Align and adjust the door if it is not level, or is not sealing properly. 
If the door is not sealed the unit may not cool properly, or 
excessive frost or condensation may form in the interior.

IMPORTANT

IMPORTANT

Properly aligned, the door’s gasket should be firmly in 
contact with the cabinet all the way around the door (no 
gaps). Carefully examine the door’s gasket to assure that 
it is firmly in contact with the cabinet. Also make sure the 
door gasket is not pinched on the hinge side of the door.

WARNING

• Do not attempt to use the door to raise or pivot 

your unit. This would put excessive stress on the 
hinge system.

• Pay special attention to the Cable Arm. Make sure not 

to over extend or damage it during door alignment.

Stainless Models (Removing Wrap)

1. Open door completely.

2. Remove the two wrap screws from the bottom of the stainless 

steel door wrap.

3. Gently pull bottom of wrap away from door.

4. The Wrap hinges on top of the door. Carefully pull wrap away 

and then up

. See below.

5. If door being adjusted houses the 

display unit, remove cable from 
display by pressing in the release tab 
on the cable connector.

Alignment and Adjustment

1. Using a T-25 Torx Bit, loosen each 

pair of Torx head screws on both the upper and lower hinge 
plate.

2. Square and align door as necessary.

3. Tighten Torx head screws on hinge.

4. If necessary re-connect display and re-install stainless steel wrap.

7 3000 Series Doors

Wrap Screws

Cable Arm

Step 1

Step 2

Door Top

Door Bottom

Press Tab  Down

T-25 Torx  Screw

T-25 Torx  Screw

Summary of Contents for U-3018WCOL-00

















Reviews: