background image

USER GUIDE

 Interior Shelves 1

SAFETY • INSTALLATION & INTEGRATION • 

OPERATING INSTRUCTIONS 

• MAINTENANCE • SERVICE

Interior Shelves

REMOVING AND INSTALLING INTERIOR 
SHELVES

For models equipped with glass shelves having recessed 
shelf supports, remove the shelves as follows:

1. Pull shelf out about 6" (1), until back of shelf clears the

“hump” on the right-hand side.

2. Tilt up right-hand edge of shelf (2).

3. Remove shelf from unit by pulling out (3).

Insert the shelves as follows:

1. To move to a different position in the unit, insert shelf

at an angle, approximately 15-20°, over the rib in the
side of the unit where you want to place the shelf.
Place the shelf into the unit at an angle to clear the
door.

2. Continue to slide the shelf into the unit at an angle

until it clears the door.

Lower the shelf and push it in completely. Ensure the 
raised edge strip is toward the rear of the unit.

NOTICE

Make sure the shelves are inserted fully into the 
unit.

The edge strip toward the rear prevents cans 
and bottles from freezing against the cold 
evaporator.

2

3

1

22

Summary of Contents for U-1224RGLS-00A




















































Reviews: