U-Line Outdoor Series Quick Start Manual & Regulatory Download Page 10

QUICK START GUIDE

7

u-line.com

General Installation

MARINE AND BI95/BI98 SERIES
LEVELING INFORMATION

NOTICE

Because these units do not have leveling legs, it 
is extremely important that they sit on a level 
surface. If they are not level, the ice mold will 
not fill evenly.

Use a level to confirm 
the unit is level. Level 
should be placed along 
top edge and side edge 
as shown.

INSTALLATION

1. Plug in the power/

electrical cord.

2. Gently push the 

unit into position. Be careful not to entangle the cord 
and water line.

3. Re-check the leveling, from front to back and side to 

side. Make any necessary adjustments.

4. Remove the interior packing material and wipe out the 

inside of the unit with a clean, water-dampened cloth.

CRESCENT ICE MAKERS, OUTDOOR SERIES AND 

ADA15IM
LEVELING INFORMATION

1. Use a level to 

confirm the unit is 
level. Level should 
be placed along top 
edge and side edge 
as shown.

2. If the unit is not level, adjust the legs on the corners of 

the unit as necessary.

3. Confirm the unit is level after each adjustment and 

repeat the previous steps until the unit is level.

INSTALLATION TIP

If the room floor is higher than the floor in the cutout 
opening, adjust the rear legs to achieve a total unit rear 
height of 1/8" (3 mm) less than the opening’s rear height. 
Shorten the unit height in the front by adjusting the front 
legs. This allows the unit to be gently tipped into the 
opening. Readjust the front legs to level the unit after it is 
correctly positioned in the opening.

INSTALLATION

1. Plug in the power/electrical cord.

2. Gently push the unit into position. Be careful not to 

kink the water supply line or entangle the cord.

1

1

Turn to Adjust

Summary of Contents for Outdoor Series


















Reviews: