manualshive.com logo in svg

U-Line H-8649, Manual, Page: 8 / 10

Share
Download
U-Line H-8649 Manual Download Page 8

PAGE 8 OF 10 

0320 IH-8649

OPERATION CONTINUED

SWING OPERATION

When you turn on the unit, the louver will swing and stop 

at a certain angle. You can press the SWING button 

to let the louver swing automatically. Press the SWING 

button again when you want the louver stopped at 

desired angle.

CHECK FILTER FEATURE

This feature is a reminder to clean the air filter (see Care 

and Cleaning) for more efficient operation. The "filter" 

indicator will illuminate after 250 hours of operation. 

To reset after cleaning the filter, press the FILTER RESET 

button and the light will go off.

FAULT CODE

If the display reads "EA," the room 

temperature sensor has failed. Contact 

Uline Customer Service at 1-800-295-5510.

If the display reads "ES," the evaporator 

temperature sensor has failed. Contact 

Uline Customer Service at 1-800-295-5510.

If the display reads "E4," the display 

panel communication has failed. 

Contact Uline Customer Service at 

1-800-295-5510.

If the display reads "P1," bottom tray is 

full. Carefully move the unit to a drain 

location, remove the bottom drain plug 

and let the water drain away. Restart 

the machine until the "P1" symbol  

disappears. If error repeats, call Uline 

Customer Service at 1-800-295-5510.

DRAINAGE

During the dehumidifying mode, you will need a 

garden hose (sold separately) to drain the condensate 

from the unit. Remove the rubber stopper from the hose 

connector. (See Figure 21)

The hose may then:

a.  Discharge into a drain that is lower than the unit.

b.  Be connected to a condensate pump (sold 

separately).

Figure 21

Garden Hose

Remove the 

Supplied 

Rubber Stopper

Summary of Contents for H-8649











Reviews:

No comments