U-Line H-8649 Manual Download Page 1

PAGE 1 OF 10 

0320 IH-8649

π

  H-8649

PORTABLE AIR 

CONDITIONER

1-800-295-5510

uline.com

WARNING! Read this section before attempting 
to operate air conditioner. Unit must be upright 
one hour prior to operating.

The power cord contains a current device that senses 

damage to the cord. To test your power cord, do the 

following:

1.  Plug in the air conditioner.

2.  The power cord will have two buttons on the plug 

head. Press the TEST button. You will notice a click as 

the RESET button pops out.

3.  Press the RESET button. Again, you will notice a click 

as the button engages. (See Figure 1)

4.  The power cord is now supplying electricity to the unit.

NOTE: Do not use this device to turn the unit 

on or off. Always make sure the RESET button 

is pushed in for correct operation. The power 

cord must be replaced if it fails to reset when 
either the TEST button is pushed or if it cannot 

be reset. If power supply cord is damaged, 
it cannot be repaired. It must be replaced. 

Contact Uline Customer Service for assistance 
at 1-800-295-5510.

SAFETY

ACCESSORIES INCLUDED

Figure 1

Exhaust Hose x 1

NOTE: Check that all accessories are included in the package 
and refer to installation instructions for usage.

Unit/Exhaust Adapter A x 1

Window/Exhaust Adapter B x 1

Foam Seal x 3

Battery (For Remote Control) x 2

Sash Lock x 1

Remote Control x 1

Window Slider Kit x 1

1/2" Screw x 4

1/2" Hex Head 

Cap Screw x 2

3/4" Screw x 2

Summary of Contents for H-8649











Reviews: