U-Line H-8262 Assembly Download Page 1

PAGE 1 OF 6 

0421 IH-8262

1-800-295-5510

uline.com

72 x 48" MEDIA 

CONFERENCE TABLE

H-8262

NOTE: Check that all parts are included. The 
four M3.5 x 10 mm screws (F) come packaged 
with the power center. 

NOTE: Table also includes flat bracket and 
six extra M6 x 15 mm bolts for the option to 

connect two tables.

1.  Fit support rail (1) over corresponding bracket on 

narrow leg (2). Secure using four M6 x 12 mm bolts 

(D). Repeat to attach remaining support rail.  

(See Figure 1)

2.  Attach both support rails (1) to wide leg (3) using 

eight M6 x 12 mm bolts (D). (See Figure 1)

NOTE: Do not fully tighten bolts until tabletop is 
attached.

3.  Place tabletop (4) on assembled frame. Attach 

tabletop (4) to narrow leg (2) using two M6 x 45 mm 

bolts (A). Secure wide leg (3) using three M6 x 45 mm 

bolts (A). (See Figure 2)

4.  Attach tabletop (4) to brackets on legs using two  

M6 x 15 mm bolts (B) per bracket. (See Figure 2)

5.  Secure tabletop (4) to support rails (1) using three  

M6 x 60 mm bolts (C) per rail. (See Figure 2)

6.  Tighten bolts (D) installed in Steps 1 and 2 with Allen 

wrench.

TOOLS NEEDED

PARTS

ASSEMBLY

Bolt x 5

M6 x 45 mm

Screw x 4

M3.5 x 10 mm

Adhesive-Backed 

Cable Clip x 4

Bolt x 12

M6 x 15 mm

Bolt x 6

M6 x 60 mm

Bolt x 16

M6 x 12 mm

Flat Bracket x 1

A

F

G

B

C

D

E

2

3

D

1

Follow hole patterns 

on frame as shown

Figure 1

Allen Wrench

(Included)

Phillips 

Screwdriver

4

3

2

1

A

B

C

Figure 2

Two Person Assembly 

Recommended

Para Español, vea páginas 3-4.

Pour le français, consulter les pages 5-6.

Summary of Contents for H-8262







Reviews: