U-Line ADA Height Compliant Series User Manual Download Page 31

USER GUIDE

Warranty 1

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • 

SERVICE

Warranty

U-LINE CORPORATION LIMITED WARRANTY

1. U-Line Corporation (“U-Line”) warrants each U-Line 

product to be free from defects in materials and 
workmanship for a period of one year (two years on 
Modular 3000 Series) from the date of purchase. 
U-Line further warrants the sealed system (consisting 
of the compressor, condenser, evaporator, hot gas 
bypass valve, dryer, and connecting tube) in each 
U-Line product to be free from defects in materials and 
workmanship for a period of five years from the date of 
purchase. 

2. During the initial one year warranty period (two years 

on Modular 3000 Series) for all U-Line products U-Line 
shall: (1) repair any product or replace any part of a 
product; and (2) for all Marine, RV and Domestic 
U-Line products sold and serviced in the United States 
(including Alaska and Hawaii) and Canada, U-Line 
shall be responsible for the labor costs performed by a 
U-Line authorized service company, incurred in 
connection with the replacement of any defective part. 
During years two through five of the warranty period 
for the sealed system, U-Line shall: (1) at U-Line’s 
option repair or replace any part of the sealed system; 
and (2) for all Marine, RV and Domestic U-Line 
products sold and serviced in the United States 
(including Alaska and Hawaii) and Canada, U-Line shall 
be responsible for the labor costs incurred in 
connection with the replacement of any defective part 
of the sealed system. All other charges, including 
transportation charges for replacements under this 
warranty and labor costs not specifically covered by 
this warranty, shall be the responsibility of the 
purchaser. This warranty extends only to the original 
purchaser of the U-Line product. The Product 
Registration Card included with the product should be 
promptly completed by you and mailed back to U-Line 
or you can register on-line at www.u-lineservice.com.

3. The warranty listed above does not apply to floor 

display models. The warranty for these models shall 
be 30 days from the date of retail purchase and only if 
U-Line’s Product Registration Card included with the 

unit is completed and mailed back or electronically 
submitted to U-Line. This 30 day warranty does not 
apply to cosmetic damages. A proof of purchase may 
be required.

4. The following conditions are excluded from this limited 

warranty: use of cleaners other than the recommended 
stainless steel cleaners and U-Line Clear Ice Maker 
cleaner; installation charges; damages caused by 
disasters or acts of God, such as fire, floods, wind and 
lightning; damages incurred or resulting from shipping, 
improper installation, unauthorized modification, or 
misuse/abuse of the product; customer education 
calls; food loss and spoilage; door and water level 
adjustments (except during the first 30 days from the 
date of installation); defrosting the product; adjusting 
the controls; door reversal; and cleaning the 
condenser.

5. U-Line product are designed to operate in ambient 

temperatures between 50°F and 100°F unless 
otherwise noted in the product manual. Exposure to 
temperatures outside this range may cause 
degradation of performance and issue such as lower ice 
production or spoiled contents are not covered under 
the terms of this warranty as a result of that exposure. 
U-Line product may not be subjected to temperatures 
below 40F without following the winterization and 
vacation shutdown procedures in the user guide.

6. U-Line’s Outdoor Limited Warranty, set forth in this 

Paragraph 6 shall apply to U-Line models deemed 
suitable for outdoor use by Underwriters Laboratory 
(“UL”) as noted in the U-Line Product Catalog, U-Line’s 
website and/or on the serial tag located inside the 
product. 

A. Outdoor product may come into contact with rain by 
virtue of outdoor use. Exposure to other sources of 
water shall also cause this warranty to be void, 
including flooding of the area in proximity of the unit 
greater than 1/8" deep in water, hurricanes, splashing 
of pool water, or directing a spray from a hose or 
similar device into and around the unit.

Summary of Contents for ADA Height Compliant Series

































Reviews: