U-Line 2175R Installation Manual Download Page 13

08/2006

13

www.U-LineService.com

2175R Refrigerator and 2175RF Refrigerator/Freezer

Electrical Specifications

CAUTION

Electrical installation must observe all state and local 
codes. This unit requires connection to a grounded (three-
prong), polarized receptacle that has been placed by a 
qualified electrician.

The unit requires a grounded and polarized 115 VAC, 
60 Hz, 15A power supply (normal household current). 
An individual, properly grounded branch circuit or circuit 
breaker is recommended. GFCI (ground fault circuit 
interrupter) is usually not required for fixed location 
appliances and is not recommended for your unit because 
a GFCI could be prone to nuisance tripping. However, be 
sure to consult your local codes.

See 

Figure 31

 for recommended receptacle location. 

WARNING

SHOCK HAZARD — Electrical Grounding Required. 

• Never remove the round grounding prong from 

the plug and never use a two-prong grounding 
adapter.

• Never use an extension cord to connect power to 

the unit.

Go on to 

7 Level the Unit

.

Leveling Information

Note: 

It is recommended that the unit is level.

1. Use a level to check the 

levelness of the unit from 
front to back and from 
side to side. Level should 
be placed along top edge 
and side edge as shown 
(see 

Figure 32

).

2. If the unit is not level, adjust the feet on the corners of 

the unit as necessary (see 

Figure 33

).

3. Check the levelness after each adjustment and repeat 

the previous steps until the unit is level. Go on to 

8 Install the Unit

.

Installation Tip

If the room floor is higher than the floor in the cut-out 
opening, adjust the rear feet to achieve a total unit rear 
height of 1/8" less than the opening’s rear height. Shorten 
the unit height in the front by adjusting the front feet. 
This allows the unit to be gently tipped into the opening. 
Readjust the front feet to level the unit after it is correctly 
positioned in the opening.

6 Prepare Power Supply

1-1/2"

7"

23-1/4"

Figure 31

7 Level the Unit

ULIN_0193_A

1

Figure 32

Turn Foot to Adjust

Figure 33

Summary of Contents for 2175R

















Reviews: