background image

12

2175DWRR

To defrost:

1. Turn the unit off.

2. Remove all products from the interior and leave the 

drawers in an open position (2" (5 cm) minimum).

3. Allow the frost to completely melt naturally. Clean the 

interior and all removed components using a mild non-
abrasive detergent and warm water solution applied 
with a soft sponge or non-abrasive cloth. 

NOTE:

 DO 

NOT use any solvent-based or abrasive cleaners. They 
will discolor or damage the interior.

4. Dampen a soft sponge or non-abrasive cloth in clean 

water and wipe down the cabinet interior and removed 
components to remove any detergent residue. Rinse the 
sponge or cloth in clean water and repeat as necessary 
until the cabinet and components are clean. 

5. When the interior is dry, turn the unit on.

Condenser Cleaning

Interval - Every Three Months

To maintain operational efficiency, keep the front grille 
free of dust and lint and clean the condenser every three 
months. Depending on environmental conditions, more 
or less frequent cleaning may be necessary.

WARNING

Disconnect electric power to the unit before 
cleaning the condenser.

To remove and replace the grille for access to the 
condenser fins, follow this procedure:

Figure 11

1. Disconnect electrical power to the unit.

2. Loosen two screws 

(Figure 11, 1)

 completely.

NOTE:

 Screws are held in the grille by o-ring retainers, 

and will not come free of the grille.

3. Remove the grille.

WARNING

DO NOT touch the condenser fins. The condenser 
fins are SHARP and can be easily damaged.

CAUTION

DO NOT use any type of cleaner on the condenser 
unit.

4. Clean the condenser coil 

(Figure 11, 2)

 using a soft 

brush with a “combing” action or vacuum cleaner. Do 
not touch the condenser coil.

5. Position the grille to align the mounting screws with 

the holes in the cabinet.

6. Secure, but do not over-tighten both grille screws.

7. Reconnect power to the unit.

Leveling

NOTE:

 It is recommended that the unit is level.

Figure 12

1. Use a level to check the levelness of the unit from 

front to back and from side to side. Place the level 
along top edge and side edge as shown 

(Figure 12)

.

Figure 13

2. If the unit is not level, adjust the feet on the corners of 

the unit as necessary 

(Figure 13)

.

3. Check the levelness after each adjustment and repeat 

the previous steps until the unit is level.

ULIN_0203_A

2

1

ULIN_0045_A

ULIN_0046_A

Summary of Contents for 2175DWRRB00





















Reviews: