background image

 

 

 

EVK-M8xCAM - User Guide 

UBX-14002462 - R07

 

Early Production Information 

 

Contact

 

 

 

Page 24 of 24

 

Contact 

For complete contact information, visit us at www.u-blox.com 
 

u-blox Offices 

 

 

 

 

North, Central and South America 

u-blox America, Inc.

 

Phone: 

+1 703 483 3180 

E-mail: 

[email protected]  

Regional Office West Coast:

 

Phone: 

+1 408 573 3640 

E-mail: 

[email protected] 

Technical Support: 

Phone: 

+1 703 483 3185 

E-mail: 

[email protected]

 

 

Headquarters 
Europe, Middle East, Africa 

u-blox AG  

Phone: 

+41 44 722 74 44 

E-mail: 

[email protected]  

Support: 

[email protected] 

 

Documentation Feedback  

E-mail:        [email protected] 

 

 

Asia, Australia, Pacific 

u-blox Singapore Pte. Ltd. 

Phone: 

+65 6734 3811 

E-mail: 

[email protected] 

Support: 

[email protected]  

Regional Office Australia: 

Phone: 

+61 2 8448 2016 

E-mail: 

[email protected] 

Support: 

[email protected] 

Regional Office China (Beijing): 

Phone: 

+86 10 68 133 545 

E-mail: 

[email protected]  

Support: 

[email protected] 

Regional Office China (Chongqing): 

Phone: 

+86 23 6815 1588 

E-mail: 

[email protected]  

Support: 

[email protected]

  

Regional Office China (Shanghai): 

Phone: 

+86 21 6090 4832 

E-mail: 

[email protected]  

Support: 

[email protected]

Regional 

Office China (Shenzhen): 

Phone: 

+86 755 8627 1083 

E-mail: 

[email protected]  

Support: 

[email protected] 

Regional Office India: 

Phone: 

+91 80 4050 9200 

E-mail: 

[email protected]  

Support: 

[email protected]  

Regional Office Japan (Osaka): 

Phone: 

+81 6 6941 3660 

E-mail: 

[email protected]  

Support: 

[email protected]  

Regional Office Japan (Tokyo): 

Phone: 

+81 3 5775 3850 

E-mail: 

[email protected]  

Support: 

[email protected]

  

Regional Office Korea: 

Phone: 

+82 2 542 0861 

E-mail: 

[email protected]  

Support: 

[email protected] 

Regional Office Taiwan: 

Phone: 

+886 2 2657 1090 

E-mail: 

[email protected]  

Support: 

[email protected] 

 

 

Summary of Contents for EVK-M8QCAM

























Reviews: