Tysso POP-650-i User Manual Download Page 105

Page: 105 / 133

- 97 -

6. Peripherals Test

The POS terminal is equipped with mainstream interfaces for the connection of peripherals and

devices. If the POS is equipped with optional peripherals (for example: Wi-Fi module, magnetic

stripe card reader, customer display, or a cash drawer). Please install the driver or perform the

tests prior or to the POS system is operational.

Note:

For more information relating to the other optional peripherals, please contact the local

representatives or technical support personnel of the nearest providers.

Please download the latest driver from TYSSO official website.

Extract the compressed file and open the folder to install the driver(s).

There are categorized folders for POS Terminal, Peripherals and Touch Screen drivers.

Select “Peripherals” to access the subfolders.

The subfolders of peripherals are as follows:

Select (double click) the folder for the peripheral required.

Summary of Contents for POP-650-i






































































































































Search results

Summary of Contents for POP-650-i

Reviews:

Related manuals for POP-650-i

Brands by name

Popular brands

Tysso POP-650-i, User Manual

Search results

Summary of Contents for POP-650-i

Reviews:

Related manuals for POP-650-i

Brands by name

Popular brands