manualshive.com logo in svg

Tycor-UPS Ty-Borealis Series, Operator'S Manual

Share
Download
Tycor-UPS Ty-Borealis Series Operator'S Manual Download Page 4

Preface

 

 

Congratulations on your choice of our emergency lighting inverter (ELI). 

This equipment has been manufactured and tested using methods and procedures 
equivalent to 
UL 924. 

This manual describes the recommended procedures for installing the ELI. 

While every effort has been made to ensure the completeness and accuracy of this manual, 
Tycor UPS assumes no responsibility or liability for any losses or damages resulting from 
the use of the information contained in this document. 

We recommend that this manual be kept with the ELI for future reference.  If any problems 
are encountered with the procedures contained in this manual, please contact our Service 
Centre before proceeding. 

This document may not be copied or reproduced without the explicit written permission of 
Tycor UPS. 

Due to technical advancements and improvements, some of the information contained in 
this manual may be changed or modified without prior notice. 

iii 

  

 

 

WARNING: This manual is intended to provide installation instructions 
only. The information contained in this manual is to be used as a guideline 
and recommendation only. Only qualified personnel should perform 
installation and maintenance. Factory authorized personnel shall inspect 
installation prior to start up and commissioning to validate warranty. 
Failure to follow this directive will void the warranty.

 

 

  

 

 

 

M4102 Ty-Borealis 8-48KW Operators Manual v1.0 2013-08-14 

 

 

Summary of Contents for Ty-Borealis Series






























































Reviews:

No comments

Brands by name

Popular brands

Load more brands