TyconSolar UPS-STL48-50 Quick Install Manual Download Page 6

6

 

 

2.

 

MAXIMUM LOAD: 

The maximum load supported by the controller is 

200W. If the load is exceeded the controller will shut down all loads and 

display an error condition. It will automatically reset after the load falls 

below 200W.

 

3.

 

OUTPUT  VOLTAGE: 

The  output  voltage  from  the  controller  on  all 

ports can be set individually to 48V or 24V in the user interface. 

 

4.

 

VENTING: 

The enclosure has vents in the upper back of the enclo-

sure and a thermostatically controlled fan and vent in the bottom of the 

enclosure. Fan airflow should be toward inside of enclosure.

 

5.

  

BATTERY  MAINTENANCE: 

The  batteries  used  in  the  UPSPro

®

  

systems don

t require any maintenance. They should last up to 5 years 

in normal use. 

Note: Never store batteries for any length of time in a 

discharged state or it will kill the battery. 

 

6.

   

BATTERY  OVERDISCHARGE

: We  highly  recommend  hooking  all 

equipment loads to the controller voltage output. This output will discon-

nect the load if the battery voltage drops below the set voltage and this 

will protect the battery from over

-

discharge. If batteries get completely 

discharged  because  the  equipment  was  connected  directly  to  the  bat-

tery, you will reduce the battery life. Discharged batteries will freeze at 

very low temperatures.

 

7.

  

ACCESSORIES

: Tycon

®

  also offers a variety of voltage conversion 

products to meet almost any need. Just visit 

tyconsystems.com

 for 

more info.

 

 

 

Limited Warranty

 

The UPSPro

®

 products are supplied with a limited 36 month warranty 

which covers material and workmanship defects. This warranty does 

not cover the following: 

 

 

Parts requiring replacement due to improper installation, misuse, 

poor site conditions, faulty power, etc.

 

 

Lightning or weather damage.

 

 

Physical damage to the external & internal parts.

 

 

Products that have been opened, altered, or defaced.

 

 

Water damage for units that were not mounted according to user 

manual.

 

 

Usage other than in accordance with instructions and the normal 

intended use.

 

 

 

NOTES

 

Summary of Contents for UPS-STL48-50









Reviews: