4
D-304286 SD-304C PG2 Installation Instructions
3. LOCAL DIAGNOSTICS TEST
Bef ore testing, separate the base f rom the cover (see Figure 3).
A.
Press the tamper switch once and release it.
B.
Put back the cover to return the tamper switch to its normal (undisturbed) position, and then secure the f ront cover to the base with the case
closure screw.
C.
Use a hammer to apply shock in close proximity to the detector and verif y the red LED blinks, indicating detection.
D.
Af ter 2 seconds the LED blinks 3 times.
The f ollowing table indicates received signal strength indication.
LED response
Reception
Green LED blinks
Strong
Orange LED blinks
Good
Red LED blinks
Poor
No blinks
No communication
IMPORTANT! Reliable reception must be assured. Therefore, "poor" signal strength is not acceptable. If you receive a "poor" signal from the
device, re-locate it and re-test until a "good" or "strong" signal strength is received.
Note: For detailed Diagnostics Test instructions, refer to the control panel Installer Guide
.
4. EVENT INDICATIONS
LED Indications
Event
Red LED ON 0.2 sec.
Tamper open / close
Red on 2 sec.
Shock
Red on 2 sec.
Open close door
Red on 2 sec.
Open close Aux input
Yellow LED on
AM detection
– diagnostic mode
Yellow LED blinks slowly (0.2 sec. ON, 30 sec. OFF)
AM detection
– Normal mode
5. MISCELLANEOUS COMMENTS
Visonic Ltd. wireless systems are very reliable and are tested to high st andards. However, due to low transmitting power and limited range
(required by FCC and other regulatory authorities), there are some limitations to be considered:
A.
Receivers may be blocked by radio signals occurring on or near their operating f requencies , regardless of the digital code used.
B.
A receiver responds only to one transmitted signal at a time.
C.
Wireless devices should be tested regularly to determine whether there are sources of interf erence and to protect against f au lts.
6. COMPLIANCE WITH STANDARDS
Compliance with Standards
The SD-304C PG2 complies with the f ollowing standards:
Europe:
EN 301 489-3, EN 50130-4, EN 300 220-2, EN 62368-1, EN 50131-5-3, EN 50130-5, EN 50131-1,
EN 50131-6 Type C, EN 50131-2-8, EN 50131-2-6, Grade 2, Class II.
Certif ied by Applica Test & Certif ication AS in accordance with EN 50131-2-6 EN 50131-2-8, EN 50131-5-3,
EN 50131-6, EN 50130-4, EN 50130-5.
UK:
This product is suitable f or use in systems installed to c onf orm to PD6662
USA:
CFR 47 part 15 (FCC)
Canada:
RSS-247, RSS-102
Hereby, Visonic Ltd. declares that the radio equipment type SD -304C PG2 is in compliance with Directive
2014/53/EU. The f ull text of the EU declaration of conf ormity is available at the f ollowing internet address:
http://www.visonic.com/download-center
.
This device complies with Part 15 of the FCC Rules and with ISED license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) This device may not cause harmf ul interf erenc e, and
(2) this device must accept any interf erence received, including interf erence that may cause undesired
operation.
Le present appareil est conforme aux CNR d'ISED applicables aux appareils radio exempts de
licence. L'exploitation est autorisee aux deux conditions suivantes :(1) l'appareil ne doit pas produire
de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique
subi, meme si le brouillage est susceptible d'en compromettre le fonctionnement.
To comply with FCC and IC RF exposure compliance requirements, the device should be located at a
distance of at least 20 cm f rom all persons during normal operation. The antennas used f or this product must
not be co-located or operated in conjunction with any other antenna or transmitter.
Le dispositif doit être placé à une distance d'au moins 20 cm à partir de toutes les personnes au cours de son
f onctionnement normal. Les antennes utilisées pour ce produit ne doivent pas être situés ou exploités
conjointement avec une autre antenne ou transmetteur.
The digital circuitry of this device has been tested and f ound to comply with the limit s f or a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmf ul interf erence in residential installations. This equipment generates, uses and can radiate radio
f requency energy and, if not installed and used in accordance with the instructions, may cause harmf ul
interf erence to radio and television reception. However, there is no guarantee that i nterf erence will not occur
