background image

3

Introduction

The Color Touchscreen LCD Annunciator for the

 

AUTOPULSE Z-20 Agent Releasing Panel* 

provides remote annunciation of the AUTOPULSE Z-20. Visual status is provided by the 
touchscreen and by the LEDs. Audible annunciation is provided through a piezo sounder. Access 

to the annunciator switch functions can be enabled or locked using the keyswitch. A maximum of 

six color touchscreen annunciators can be installed on an AUTOPULSE Z-20 panel.

*AUTOPULSE Z-20 Agent Releasing Panel, from this point on, will be referred to as the 

AUOPULSE Z-20.

Compatibility

The AUTOPULSE Z-20 must be at revision 3.02.07 or higher to support the Color Touchscreen 
LCD Annunciator.
The following annunciators, boxes, and brackets are compatible with the

 

AUTOPULSE Z-20:

Reference 
Documents

Refer to the following documents for more information on how to program and

 

use the remote 

annunciator.

In this 
publication

Introduction ................................................. 3 Compatibility ............................................... 3
Reference Documents  
................................ Wire Length Tables  ..................................... 7
Module Overview  ........................................ Communication Wiring Length Tables  ........ 8
General Mounting Information  .................... Address Setting ........................................... 8
General Wiring Guidelines .......................... Mounting Instructions ................................ 10
Specific Wiring Guidelines  .......................... Verification Procedure ............................... 10
Wiring .......................................................... Remote Annunciator Specifications  .......... 11

Part Number

Description

4606-9202AR

AUTOPULSE

 

Color Touchscreen LCD Annunciator, Red

2975-9461

AUTOPULSE

 

Color Touchscreen LCD Annunciator, Surface Mount Box, 

Red

2975-9463

AUTOPULSE Color Touchscreen LCD Annunciator, Retrofit, Semi-flush 
bracket, Red

Document Number

Title

579-1165AR

AUTOPULSE Z-20 Operator’s manual

579-1167AR

AUTOPULSE Z-20 Programmer’s manual

Color Touchscreen LCD Annunciator Installation Instructions

Summary of Contents for AutoPulse Z-20













Reviews: