background image

MM102014V1, Rev. G 

4.

 

Do not operate the radio in explosive atmospheres (gases, dust, fumes, etc.) or near explosive blasting 
caps. 

5.

 

Do not attempt any unauthorized modification to the radio. Changes or modifications to the radio may 
cause harmful interference. Only qualified personnel should service the radio. 

6.

 

Always use M/A-COM authorized accessories (antennas, control heads, speakers/microphones, etc.). 
Use of unauthorized accessories can cause the FCC RF exposure compliance requirements to be 
exceeded. 

The information listed above provides the user with the information needed to make him or her 
aware of a RF exposure, and what to do to assure that this radio operates within the FCC exposure 
limits of this radio. 

2.2  COMMON HAZARDS 

The operator of any mobile radio should be aware of certain hazards common to the operation of 
vehicular radio transmissions. Possible hazards are: 

 

Explosive Atmospheres 

Just as it is dangerous to fuel a vehicle with the motor running, be sure to turn the radio OFF while 
fueling the vehicle. Do NOT carry containers of fuel in the trunk of the vehicle if the radio is mounted 
in the trunk. 

 

Interference To Vehicular Electronic Systems 

Electronic fuel injection systems, electronic anti-skid braking systems, electronic cruise control 
systems, etc., are typical types of electronic devices that can malfunction due to the lack of protection 
from radio frequency (RF) energy present when transmitting. If the vehicle contains such equipment, 
consult the dealer for the make of vehicle and enlist his aid in determining if such electronic circuits 
perform normally when the radio is transmitting. 

 

Electric Blasting Caps 

To prevent accidental detonation of electric blasting caps, 

DO NOT 

use two-way radios within 1000 

feet (304.8 meters) of blasting operations. Always obey the "Turn Off Two-Way Radios" signs posted 
where electric blasting caps are being used. (OSHA Standard: 1926.900) 

 

Radio Frequency Energy 

To prevent burns or related physical injury from radio frequency energy, do not operate the 
transmitter when anyone outside of the vehicle is within the minimum safe distance from the antenna 
as specified in Table 2-1

 

Vehicles Powered By Liquefied Petroleum (LP) Gas 

Radio installation in vehicles powered by liquefied petroleum gas, where the LP gas container is 
located in the trunk or other sealed-off space within the interior of the vehicle, must conform to the 
National Fire Protection Association Standard NFPA 58. This requires: 
a.  The space containing radio equipment is isolated by a seal from the space containing the LP gas 

container and its fittings. 

b.  Outside filling connections are used for the LP gas container. 
c.  The LP gas container space is vented to the outside of the vehicle. 

 

Vehicles Equipped With Airbags 

For driver and passenger safety, avoid mounting the control head (or any other component) above or 
near airbag deployment areas. In addition to driver-side and passenger-side front-impact airbags, 
some vehicles may also be equipped with side-impact airbags. For occupant safety, verify the location 
of all airbags within the vehicle before installing the radio equipment. 

Summary of Contents for M/A-COM M-803

































































Reviews: