manualshive.com logo in svg

TYAN GN70-B7086, Service Manual

Share
Download
TYAN GN70-B7086 Service Manual Download Page 30

 

http://www.tyan.com

 

30 

1.5.4      Jumpers & Connectors 

 

Connectors 

1. LAN port#3 (IPMI) and USB 3.0 ports 

17. 4-pin Fan Connector(CPU0_FAN) 

2. 7-pin vertical SATA 3.0 Connector 
(SATA5,upper/SATA4 down) 

18. 8-pin Power Connector(PW2) 

3. VGA Port / COM Port   

19.

 

4-pin Fan Connector(SYS_FAN3) 

4. 4-pin Fan Connector(SYS_FAN4) 

20. 4-pin Fan Connector(SYS_FAN2) 

5. ID Button(SW2) 

21. 4-pin Fan Connector (SYS_FAN1) 

6. Clear Button(SW1) 

22. 8-pin Power Connector(PW3) 

7. LAN Port#1(LAN1) 

23. PCIE Header (PCIEx4 From CPU1 SAS 
HD1,right/ SAS HD2,left) 

8. LAN Port#2(LAN2) 

24. 4-pin Fan Connector(CPU1_FAN) 

9. ID LED 

25.USB 2.0 Header(USB2_HD1) 

10. 4-pin Fan Connector(SYS_FAN5) 

26.PSMI Connector(PSMI_HD1) 

11. TYAN Module Header 

27. 24-pin Power Connector(PW1) 

12. BMC LED 

28. USB 3.0 Header(USB3_HD1) 

13. COM Port(COM2) 

29. TYPE_A USB Header(TYPEA_USB3) 

14. Fan IO Header(FAN_HD1) 

30. 4-in-1 Mini SAS Connector(SSATA0-3) 

15. Front Panel Header(FP_HD1)/LAN2 
LED Header(LAN_LED_HD1) 

31. PCH SATA SGPIO 
Header(SGPIO1,SATA0-5) 

16. IPMB Connector(IPMB_HD1) 

32. 4-in-1 Mini SAS Connector(SATA0-3) 

Headers/Jumpers

 

a. PSU Alert Disable Jumper (3PHD_9) 

e. MIC Card Jumper (3PHD_3) 

b. BIOS Security Jumper(3PHD_4) 

f. ID_LED Button Header (2PHD_2) 

c. ME Recovery Mode Jumper 
(3PHD_6) 

g. Chassis Intrusion Header (2PHD_1) 

d. Buzzer Disable Jumper (4PHD_1) 

 

Slots

 

A.

 PCI-E Gen3 x8 MEZZ slot f/ CPU0 for 

LAN card

 

CPU0 DIMM      G/H/I/J 

B.

 PCI-E Gen3 x16 slot(x16 link) f/ 

CPU1

 

CPU1 DIMM      K/L/M/N 

C.

 PCI-E Gen3 x16 slot(x16 link) f/ 

CPU0

 

 

D.

 PCI-E Gen3 x4 slot(x8 link) f/ CPU1

 

 

E.

 PCI-E Gen3 x4 slot(x8 link) f/ CPU0

 

 

F.

 PCI-E Gne3 x8 MEZZ Slot f/ CPU0 for 

SAS card

 

 

 
 

Summary of Contents for GN70-B7086



























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands