TYAN B7018Y290D2 Page 22 Manual Download

Page: 22 / 76

http://www.tyan.com

1.5.2 System Rear View (Per Node)

blue ID LED: When the ID (UID) button on the front panel is

pressed, the dual-color Power LED and the blue ID LED will
turn blue. The technical personnel can easily locate the system
on the rack, disconnect cables from the system, and remove it
from the rack for later repair.

LAN LED: The three onboard Ethernet ports have green and

amber LEDs to indicate LAN status. The table below illustrates
the different LED states.

Ethernet LAN Link/Activity LED

Description

Left: slow blinking green
Right: Off

10 Mbps Link

Left: blinking green
Right: Off

10 Mbps Activity

Left: slow blinking green
Right: green

100 Mbps Link

Left: blinking green
Right: green

100 Mbps Activity

Left: slow blinking green
Right: amber

1000 Mbps Link

Left: blinking green
Right: amber

1000 Mbps Activity

Left: Off
Right: Off

No Link

Summary of Contents for B7018Y290D2













































































Search results

Summary of Contents for B7018Y290D2

Reviews:

Related manuals for B7018Y290D2

Brands by name

Popular brands

TYAN B7018Y290D2, Manual

Search results

Summary of Contents for B7018Y290D2

Reviews:

Related manuals for B7018Y290D2

Brands by name

Popular brands