background image

P.2

Parts List

COVERING:--

TOUGHLON STL 100 WHITE

TOUGHLON STL 311 FERRARI RED

TOUGHLON STL 201 BLACK

TOUGHLON STL 250 BLUE

TOUGHLON STL 331 CUB YELLOW

10. FUEL TANK 450cc -- 1 set
      CABLE TIE 1.5x5x400mm -- 1 pc.
      DOUBLE-SIDE TAPE 40x100mm -- 1 pc.
11. 

SILICON GROMMETS PL1265035 -- 4 pcs

      SPINNER Ø82mm PL2111082 -- 1 set

      SCREW PWA2.6x12mm -- 4 pcs

      COWLING --1 pc.

      TRANSPARENT 3D TEMPLATE -- 1 pc.

12. 

LINKAGE CONNECTOR Ø2.1mm w/ set screw -- 1 set

13. 

STRAPER PL4112102 -- 2 pcs

      FUEL TUBE D6x5mm -- 2 pcs
      PUSHROD CONNECTOR PL4410010 -- 1 set    
      PUSHROD Ø1.8x75mm (For Elevator) -- 1 pc. 
      SPONGE 60x70x105mm -- 2 pcs
14. SCREW HM4x30mm -- 2 pcs
      SCREW HM4x55mm -- 2 pcs
      WASHER d4xD15mm -- 4 pcs
15. SCREW PM3x13mm -- 1 pc.
      WASHER d3xD7mm -- 1 pc.

      AIR SCOOPY -- 1 pc.

16. DECALS: A341 DEC -- 1 set

 1. MAIN WING -- 1 pair
 2. PUSHROD Ø1.8x95mm w/ Threads (For Aileron) -- 2 pcs
     TRI-HORN PL4111221 -- 2 sets
     SCREW PB2x18mm -- 4 pcs
     SCREW PB2x14mm -- 2 pcs
     SCREW PWA2.3x8mm -- 8 pcs
     CLEVIS PL4112103 -- 2 pcs 
     FUEL TUBE D6x5mm -- 4 pcs
     

STRAPER PL4112102 -- 2 pcs

     SERVO MOUNTING PANEL PL5310000 -- 1 pair
     MAIN LANDING GEAR COVERS -- 1 pair
     RETRACTABLE  LANDING GEAR COVERS -- 1 set
     WING JOINER 8x22.7x219mm -- 1 pc.
     180mm Y-CORD KW0021800 -- 1 pc.
 3. STABILIZER & ELEVATOR -- 1 set
     FUSELAGE -- 1 pc.
 4. VERTICAL FIN & RUDDER -- 1 set
 5. PUSHROD Ø1.8x500mm w/ Threads (For Elevator) -- 2 pcs
     SCREW PB2x14mm -- 4 pcs
     SCREW PB2x12mm -- 2 pcs
     CLEVIS PL4112103 -- 2 pcs
     TRI-HORN PL4111221 -- 2 sets
     FUEL TUBE D6x5mm -- 2 pcs
 6. PUSHROD Ø1.8x630mm w/ Threads (For Rudder) -- 1 pc.
     CLEVIS PL4112103 -- 1 pc.
     SCREW PB2x12mm -- 3 pcs
     TRI-HORN PL4111221 -- 1 set
     FUEL TUBE D6x5mm -- 1 pc.
 7. TAIL LANDING GEAR -- 1 set
     TAIL WHEEL Ø25mm -- 1 pc.
     COLLAR Ø2.1mm w/ Set Screw -- 1 set
     SCREW PA3x14mm -- 2 pcs
     SCREW PM2x10mm -- 1 pc.
      ALUMINIUM PLATE 0.3mm -- 1 pc.
      M2 NUT -- 1 pc.

 8. 

ENGINE MOUNT PL5111050 -- 1 set 

     SOCKET HEAD SCREW M4x25mm -- 4 pcs
     WASHER d4xD9mm -- 4 pcs
 9. THROTTLE PUSHWIRE Ø1.2x500mm -- 1 pc.
      PLASTIC TUBE d2xD3x360mm -- 1 pc.

      SCREW PM3.5x30mm -- 4 pcs
      WASHER d3.5xD8mm -- 8 pcs

      M3.5 NUT -- 8 pcs

A341PO31811702

Summary of Contents for P-51D Strega-40

















Reviews: