If heli’s nose spins to the
left while hovering...
move the trim tab forward
until heli holds its heading.
If heli’s nose spins to the
right while hovering...
move the trim tab backwards
until heli holds its heading.
Turn to Right
Gently move direction
stick to the right.
Turn to Left
Gently move direction
stick to the left.
Move forward
Gently move direction
stick forwards.
Move backwards
Gently move direction
stick backwards.
•This product is designed to be used exclusively indoors. DO NOT ATTEMPT TO FLY OUTDOORS.
•Always turn your transmitter on fi rst, before turning on your helicopter.
•During fl ight, focus on the helicopter, not your transmitter.
•Recommended for children aged 14+ unless under direct adult supervision.
•Always turn your helicopter off before turning off your transmitter.
•Do not attempt to fl y in direct sunshine or strong lighting as it may affect the infrared control system.
•Do not cover the infrared sender on the remote control while fl ying. There must be a direct line of sight
between the transmitter and the helicopter.
•Avoid fl ying in rooms with air currents caused by open windows, heating or airconditioning.
•Do not fl y near or over spectators.
Transmitter layout
On/Off switch
A,B,C channel select switch
Direction stick
Throttle stick
Infrared sender
Charging lead for heli.
(Stored under sliding cover.)
Trim slider
Instructions
OFF
ON
Load 6AA batteries in the
transmitter and replace cover.
Make sure the +positive and
-negative are installed correctly..
Plug charge lead on
transmitter into
charge jack on side of
MicroTwister helicopter marked CHA.
Lead only fi ts one way.
DO NOT FORCE IT!
Switch must be OFF to
charge heli.
Heli will not charge if
switch is ON
Turn transmitter ON
Red light/No heli=Power is ON
Green light/with Heli= Charging
No Green light/with Heli=Charged
Unplug charge lead after heli is
charged and turn of transmitter.
Turn Heli ON
Always turn the heli ON
after the transmitter is ON
When you have fi nished
fl ying always turn the
heli OFF fi rst and the
transmitter OFF last
.
Turn transmitter ON
Always turn the trans-
mitter ON fi rst.
When you have fi nished
fl ying turn the heli OFF
fi rst and the transmitter
OFF last
.
Up to three Micro Twister helicopters can be
fl own at the same time, just select a different
A,B or C band setting for each heli prior to
turning on transmitter or heli.
CAUTION:You may have to leave the room
to arm the other heli’s as the infrared control
may get confused if more than one heli is
armed at the same time in the same room.
Arm heli (make ready to fl y)by moving the throttle stick all
the way forward then all the way down
Hold heli by landing skids while arming to prevent it fl ying
off without warning.
Your Micro Twister Heli is ready to fl y!
+
+
+ +
+ +
OFF
ON
Charging - Charge time 30mins, do not leave unattended.
Flying your Micro Twister
Micro Twister Heli may also be charged with supplied USB lead
connected to your computer.
USB Red light/No heli= Power Available
USB Red light/with Heli= Charged
USB No light/with Heli=Charging
Load Batteries in transmitter
MOPS - Motor Overload Protection System
Your Micro Twister is equiped with MOPS.
In the event of a crash or something preventing the main rotor blades from spinning, MOPS will cut
power to the heli.
Simply turn your Micro Twister OFF and ON and it will be ready to fl y again.
Arming your Micro Twister Helicopter
Three Micro Twisters
may fl y at once.
Hover Up
Gently move throttle
stick forward to increase
helicopter height
Hover Down
Gently move throttle stick
backward to decrease
helicopter height
