background image

WARNING! 

PARENTAL SUPERVISION 

AND APPROPRIATE USE

Like any moving product, rides made from 
Infento parts can be dangerous if due care 
and attention is not paid. To reduce the risk 

of serious injury: use only under close adult 
supervision. Parents must review the following 
warnings and instructions with each Infento 
ride that is being build. It is your responsibility 
to review this information and make sure that 
all riders understand all warnings, cautions, 
instructions and safety topics, and assure that 
young riders are able to safely and responsibly 
use this product. Infento recommends that you 
periodically review and reinforce the infor-
mation in this manual with younger riders, and 
that you inspect and maintain your child’s 
Infento rides to insure their safety.

WARNING! 

RIDING ON 

INFENTO RIDES CAN BE A 
DANGEROUS ACTIVITY

Riding on Infento rides can be a dangerous 
activity. Certain conditions may cause the equip-
ment to fail without fault of the manufacturer. 
Rides made from Infento parts can and are 
intended to move, and it is therefore possible to 
lose control, fall off  and/or get into dangerous 
situations that no amount of care, instruction or 
expertise can eliminate. If such things occur you 
can be seriously injured or die, even when using 
safety equipment and other precautions. Ride at 
your own risk and use common sense. 

WARNING! 

NO LIABILITY FOR 

CONSTRUCTED RIDES THAT 
DIFFER FROM OUR MANUALS

The rides that you can fi nd in our manuals have 
been tested by offi

  cial independent testing 

agencies. We will not be responsible or liable, 
directly or indirectly, in any way for any loss or 
damage of any kind incurred as a result of your 
decision to build constructions or rides that 
diff er from the offi

  cial rides that we show in our 

manuals. 

ASSEMBLY – SUBSECTION

WARNING! 

OUR KITS 

CONTAIN SMALL PARTS

This package contains small parts which, before 
assembly, present a choking hazard to children 
under the age of three. Care should be taken 

during unpacking and assembly to insure that 
all small parts and plastic bags are accounted 
for and kept out of the reach of children.

WARNING! 

TO AVOID 

SERIOUS INJURY:

1.

 Toys are to be assembled by an adult using 

Infento manuals. 

2.

 All fasteners (bolts and nuts) should be 

fully tightened.

3.

 It is the responsibility of the adult who 

assembles this bicycle to properly install all    
parts included in the factory sealed shipping  
carton and to make the adjustments to the 
functional parts such as handle bar and seat  
and chain when necessary.

USE – SUBSECTION

WARNING! 

 TO AVOID 

SERIOUS INJURY:

1. 

Continuous adult supervision is 

required.

2.

 Only ride constructed rides that have been 

built according to the instructions given in the 
offi

  cial Infento manual.

3.

 Never exceed the maximum weight. You can 

fi nd the maximum weight for every specifi c ride 
in our manual.

4.

 Always check the manual to see the minimum 

and maximum age as well as the minimum and 
maximum length for every specifi c ride.

5.

 Always wear safety equipment such as a 

helmet, knee pads and elbow pads. We 
recommend riders always wear a properly fi tted 
helmet that complies with local or national 
guidelines or laws. Keep chinstrap of helmet 
securely buckled.

6.

 Always wear closed toed shoes (lace-up 

shoes with rubber soles), never ride barefooted 
or in sandals, and keep shoe laces tied and out 
of the way of the wheels.

7.

 Avoid streets and surfaces with water, sand, 

gravel, dirt, leaves, and other debris. Wet we-
ather impairs traction, braking and visibility.

8. 

Excessive exposure to sunlight, temperatures 

below 0 degrees Celsius, water, sand, gravel, 
dirt, leaves, and other debris can damage, 
shrink, expand or weaken parts. Keep your ride 
in a dry environment with proper heating. 

9.

 Avoid sharp bumps, drainage grates and 

sudden surface changes. Your Infento ride may 
suddenly stop.

10.

 Ride on smooth, paved surfaces away from 

motor vehicles. Wet, slick or uneven and rough 

SAFETY 

SECTION

surfaces may impair traction and contribute to 
possible accidents. 

11. 

Never risk damaging surfaces, such as carpet 

or fl ooring, by use of an Infento ride indoors. 

12.

 Never use near motor vehicles, streets, 

roadways, alleys, swimming pool areas, hills, 
steps, sloped driveways, inclines and public 
highways.

13.

 Watch out for pedestrians, skaters, skate-

boards, scooters, bikes, children or animals who 
may enter your path, and respect the rights and 
property of others. 

14.

 Avoid excessive speed associated with 

downhill rides.

15.

 Do not use at night or in periods with 

reduced visibility.

16. 

Before every use, please make sure that 

the complete ride and all joints have been 
assembled tightly, as with use, joints may 
wear out.

17.

 Before using your Infento ride, please check 

that the screws are tightened securely.

18.

 It’s your own responsibility if you modify the 

product other than manufacturer’s instructions. 

19.

 Maintain a hold on the handlebars at all times.

20.

 Brake will get hot from continuous use. 

Do not touch after braking.

21.

 Periodically check hardware and tighten 

if necessary. Replace worn or broken parts 
immediately.

22.

 Skill is required to avoid falls or collision 

causing injury to the user and third parties.

23.

 Check operation of breaks every time 

before bicycle is ridden.

24.

 Check local laws before you start with riding.

25.

 Never tow wagons, other vehicles, or 

children on skates or skateboards. 

26.

 Make certain that anyone who uses an 

Infento ride has been fully instructed in its 
operation.

27.

 Instruct your child on how to use the 

breaks.

28.

 Do not perform stunts.

29.

 Never use headphones or a cell phone 

when riding. 

30. 

Only one rider at a time on an Infento ride.

31. 

Do not allow children to stand on the 

product at any time.

FAILURE TO USE COMMON SENSE AND 
HEED THE ABOVE WARNINGS INCREASES 
RISK OF SERIOUS INJURY. USE WITH 
APPROPRIATE CAUTION AND SERIOUS 
ATTENTION TO SAFE OPERATION.

Summary of Contents for Infento

































Reviews: