background image

22

http://www.jperkinsdistribution.co.uk

TWISTER

Aggressor 

2.4

 

Twister Aggressor2.4

 

TROUBLESHOOTING

MAIN ROTOR DOES NOT TURN

▼ 

Check throttle stick and trim lever are in the fully down position before advancing the throttle stick.

▼ 

Check all electrical connections and that the '3-in-1' receiver crystal is seated securely in the socket in 

the '3-in-1' unit.

▼ 

Check that both motor pinion gears are still engaged with the main drive gears.

▼ 

Check Li-po battery is charged.

▼ 

Check state of transmitter batteries.

▼ 

Check green light on 3-in-1 unit is glowing.

HELICOPTER SPINS UNCONTROLLABLY

▼ 

Check main gear retaining set screws

▼ 

Check Gyro gain trimmer (3-in-1 unit) to ensure gyro gain is set to approximately 90%.

HELICOPTER ACCELERATES AWAY WHEN STICKS ARE NEUTRAL

▼ 

Check that swashplate is level. Adjust trimmers and/or adjust swashplate cyclic links length if neces-

sary.

VIBRATION

▼ 

Bent main shaft(s)—the tail boom and undercarriage will vibrate if the main shaft(s) is/are bent. Replace 

the main shaft(s) and gear unit if you suspect a bent main shaft.

▼ 

Flybar is bent—straighten or replace if badly bent.

▼ 

Main blades out of balance—check that blades are not bent or broken.

LITHIUM POLYMER BATTERY SAFETY

Before Charging Li-po’s

  Before charging your battery check for any damage e.g. check if the battery has expanded or swollen 

in size or if the battery cells have been punctured. If any of the above is true: DO NOT CHARGE THE 

BATTERY!

Charging Li-po’s

  Only use a charger designed to charge Lithium polymer batteries. Never use a nicad or other charger 

as this is very dangerous.

  Never attempt to charge at a rate faster than that recommended in the instructions. Check that the 

battery 

cell count matches the 

charger 

cell count switch (if fitted).

  Never charge unattended. Always stay with your battery whilst charging in case of overheating or fire.

  Charge on a safe surface or container (e.g. old unused microwave oven). Charge 

only 

on non-flamma-

ble surfaces, e.g. concrete floor preferably outdoors, or in a pyrex cooking dish with the battery placed 

on a bed of sand, or in a fireplace. Never charge inside a car!

  Switch off charger if battery gets too hot. If the battery becomes hot to the touch during charging, 

disconnect and switch off immediately.

  Extinguish fires with sand. If something goes wrong and your battery catches fire, always have sand 

from a fire bucket at hand to douse the flames. Do NOT use water!

Using Li-po’s

  Do not modify/change any part of the battery or lead. Do not remove its heat shrink protective covering.  

Removal or modification may damage the battery and will invalidate any warranty claim.

  Do not place this battery near fires or anything with high temperatures.

  Do not charge batteries while you are driving and do not store batteries in any type of motor vehicle.

  Do not let the battery get wet or become submerged in any type of liquid.

  Do not carry loose batteries in your pocket or bag as they could short-circuit against other items.

  If you should get electrolyte from the cells on your skin, wash thoroughly with soap and water. If in your 

eyes, rinse thoroughly with water. Seek medical assistance.

Summary of Contents for Aggressor2.4





























Reviews: