manualshive.com logo in svg

Twinno T4046, Operating Manual

Share
Download
Twinno T4046 Operating Manual Download Page 14

12

Field Calibration
Select on-site calibration methods: 

ս

Linear calibration

վ

, 

ս

Offset adjustment

վ

, 

ս

linear

adjustment

վ

.

Field Calibration

When the data from laboratory or portable instrument are input into this item, the instrument will 
automatically correct the data.

Calibration results:

Confirm: When the "ENT" icon is green, press

 

ս

ENT

վ

 

to confirm.

Cancel: Press the

 

սӜվ

 

key to shift the green icon to ESC, and press

 

ս

ENT

վ

 

key to confirm.

Offset adjustment

Compare the data of laboratory or portable instrument with the data of instrument 
measurement,if there are errors, the error data can be modified by this function.

Linear adjustment

Linear values after "field calibration" are stored in this item, with factory data of 1.00.

Fluorescence Dissolved Oxygen

Field Calibration

DO: 7.00
Vol: 0mV
Temp: 25.0

Calibrating

Fluorescence Dissolved Oxygen

Field Calibration

Cal Resault

：

Slope 3:  1.00

ENT

ESC

0.001

Fluorescence Dissolved Oxygen

Field Calibration

Input Value

：

Summary of Contents for T4046





























Reviews:

No comments

Brands by name

Popular brands

Load more brands