background image

 FIREPLACE  LOCATION

When choosing a location for your new fireplace,

 ensure that the general instructions are followed. 

Also, for best effect, install the fireplace out of 

direct sunlight.

                   

                        Cold climate installation recommen- 

                        dation: when installing this unit 

                        against a non-insulated exterior wall 

                        or chase, it is mandatory that the 

                        outer walls be insulated to conform 

                        to applicable insulation codes.

ELECTRICAL CONNECTION

A 15 AMP, 120 Volt, 60 Hz circuit with a properly 

grounded outlet is required. Preferably, the fireplace 

will be on a dedicated circuit as other appliances on 

the same circuit may cause the circuit breaker to trip 

or the fuse to blow when the heater is in operation. 

The unit comes standard with 6 feet (1.8 m) three 

wire cord, exiting from the rear of the fireplace. 

Plan the installation to avoid the use of an extension 

cord. If an extension cord must be    

used, it must be a minimum 14 AWG ; three wires

with grounding type plug connector and rated 

not less than 1875 Watts. The cord shall not be

more than 20 feet (6 m) in length.

ELECTRICAL SPECIFICATIONS

Voltage:         120VAC, 60Hz

Amps:            12.5 Amps

Watts:            1500 Watts

CLEARANCE TO COMBUSTIBLES

Keep electrical cords, drapery, furniture and other 

combustibles at least 3 feet (0.9 m) from the front of the 

heater and away from the sides.

CLEANING TRIM

Clean the metal trim using a soft cloth, slightly 

dampened with citrus oil based product and buff with 

a clean soft cloth. DO NOT use brass polish or 

household cleaners as these products will damage 

the metal trim. Citrus oil based products can be 

obtained at supermarkets or hardware stores.

MAINTENANCE

WARNING: Make sure the power is turned off before proceeding. Any electrical repairs or 

rewiring of this unit should be carried out by a licensed electrician in accordance with 

national and local codes.

If repairing or replacing any electrical component or wiring, the original wire routing, color 

coding and securing locations must be followed.

WARNING: Electrical outlet wiring must comply with local building codes and other applicable

 regulations to reduce the risk of fire, electrical shock and injury to persons.

WARNING: Do not use this fireplace if any part of it has been under water. Immediately call a 

qualified service technician to inspect the fireplace and replace any part of the electrical system.

Warning: Disconnect power before attempting any maintenance or cleaning to reduce the risk

 of fire, electrical shock or personal injury.

MAINTENANCE

 Warning: During any service of this appliance, the power to the unit must be turned off. 

First turn the main power switch to the “OFF” position. Then remove the electrical plug from 

the wall outlet.

E-5

Meijer.com

Summary of Contents for 35HF500GRA- BLK











Reviews: