background image

Assembly Instructions VERA ORF900

17

Copy and translation of the original CE Conformity Declaration:

We hereby declare that the below-referenced components by virtue of their design and con-
struction, and in the configuration placed on the market by us, satisfy the safety and health 
requirements of the applicable EC directives. This declaration becomes invalid in case of modi-
fications that have not been approved by us.

This declaration applies to the following components

•  VERA ORF900

as well as all model variants based on these, provided that they correspond to the original 
factory models and have not been technically modified in any way.

Applicable directives:

• 2001/95/EG

Applicable national standards and technical specifications

• DIN EN 18 800
• DIN EN ISO 12 100
• BGV C1 / BGI 810-3

Ludwigsburg, Germany, April 1st, 2014

 

       Tobias 

Wüstner

If you have any question regarding the disposal of used devices, please contact us under the 
following telephone number: 

+49 (0) 71 41 - 48 89 89 0

In countries outside of the European Union, comply with local regulations. 

6. CE Declaration of Conformity

7. Disposal

Summary of Contents for VERA ORF900



















Reviews: