manualshive.com logo in svg

TVLogic LEM-250A, Operation Manual

Share
Download
TVLogic LEM-250A Operation Manual Download Page 36

36  FHD OLED Reference Monitor   

6. Other Functions

[6] Firmware Upgrade

[7] COLOR CALIBRATION

 

●

The USB portable storage device (Thumb  

  drive) is needed for Firmware Upgrade.

 

●

Select the PAGE III of [SYSTEM] menu to  

 activate.

1. Connect the USB to the USB Slot on the front 

    of the monitor.

2. Set the [S/W UPGRADE] as [ON].

3. The [S/W UPGRADE START] activates when 

    the USB connection is completed. 

 

●

The Probe(USB) is needed for Auto  

 

  Color Calibration.

 

●

Select the PAGE III of [SYSTEM] menu to  

 activate.

1. Connect the Color Probe to the USB Slot on  

    the front of the monitor.

    A supported USB probe (K-10, i1Pro)  is    

    needed for Auto Color Calibration

2. Set the [DEVICE] as the Color Probe which  

    will be connected.

3. Set the [Color Calibration] as [On].

4. Then the USB Color Probe is searched    

    automatically.

5. The [Color Calibration] activates when the  

    USB connection is completed. 

4. Select the [S/W UPGRADE START] to start the 

    firmware update.

* While the Upgrade is conducting, the monitor

  screen turns off and the monitor stops    

 functioning. 
* When the Upgrade is completed, the monitor 

 reboots. 
* The Upgrade process takes about 20~30 

  minutes according to the Firmware type.

6. Set the value of [TARGET LUMINANCE], [K-10  

    CHANNEL] and [COLORSPACE].

7. Select the [CALIBRATION START] to start the  

    calibration. 

* After the calibration starts, various patterns  

  come on the screen and conduct the color  

 calibration. 
* The Color Calibration takes about 20~60   

 minutes.

LEM-250A

LEM-250A

SDI A

SDI A

OFF

OFF

OFF

O ON

PAGE IV >> PAGE V 

COPY DATA

CAL. LOG COPY START

S/W UPGRADE

S/W UPGRADE START

PAGE IV >> PAGE V 

COPY DATA

CAL. LOG COPY START

S/W UPGRADE

S/W UPGRADE START

LEM-250A

SDI A

PAGE III >> PAGE IV 

DEVICE

COLOR CALIBRATION

TARGET LUMINANCE

K-10 CHANNEL

COLORSPACE

CALIBRATION STARAT

MEASUREMENT START

Y:000.00 x:0.000 y:0.000

LEM-250A

SDI A

PAGE III >> PAGE IV 

DEVICE

COLOR CALIBRATION

TARGET LUMINANCE

K-10 CHANNEL

COLORSPACE

CALIBRATION STARAT

MEASUREMENT START

Y:000.00 x:0.000 y:0.000

ON

OFF

80 cd/m2

     00:           

REC-709

ON

ON

80 cd/m2

     00:           

REC-709

Summary of Contents for LEM-250A









































Reviews:

No comments

Brands by name

Popular brands

Load more brands