TV Bedstore ESTON OTTOMAN TV BED Assembly Instructions Manual Download Page 19

Page 19 of 20

TV BED SAFETY INFORMATION  

GENERAL INFORMATION

It is very important not to place any vessel containing liquids, e.g. drinks or vase of flowers, on top of the TV footboard 
which may accidentally spill and enter the TV compartment as this could cause damage to the TV and/or the TV lifting 

equipment. 
If this happens, please contact your retailer. 
Do not expose the bed to an undue level of heat - keep away from radiators. 
Never allow anyone to sit on the foot end of the bed - keep children well away from moving parts.
To keep bed clean, we recommend that it be wiped over with a slightly dampened cloth or if fabric, use a light vacuum 
cleaner; disconnect power before cleaning. 
Supplied with the bed is a remote control to operate the TV Lift

/Audio system

 and when you fit your own TV there is a 

remote control to

 

operate it as well. Both these remotes use batteries - there are no batteries in the rest of the equipment. 

There are strict controls for disposal of batteries - your local council can advise on how to safely dispose of them. 
Never burn batteries on an open fire as they could explode.

IMPORTANT POWER INFORMATION

It is essential that the Mains Power Lead ( G) is connected to an earthed socket be it a wall socket or extension lead - 

otherwise there is risk of damage or even electric-shock.

The socket providing the power must be accessible at all times in case you need to switch off the power quickly.

During an electrical or lightening storm - disconnect the power completely as a precaution.

Always un-plug the power when going on holiday or when the bed is not used for an extended period.

If you have young children in the home always disconnect the power at the wall socket for extra safety.

Power outlets, extension leads or adapters must not be overloaded beyond their limit - this can result in fire or electric shock. 

Leads supplied with this bed, or other approved mains powered extension leads used to power the equipment, must not be 

placed where they can be walked on - this is dangerous and could lead to accidents.

Do not interfere with or modify any cables already fitted and do not add any extra media leads unless they are routed 

through the ducts as shown in Step 

7

. All leads must be tightly connected to back of TV, never hanging loose.

Never touch moving parts or any part of the equipment - if something needs to be checked, disconnect the power first.

Do not insert anything into the footboard as this could seriously damage the TV and/or the TV lifting equipment and could, if 

done carelessly, cause serious damage or injury.

If the equipment doesn't operate normally or if there is  any  unusual noises, disconnect the power. 

TELEVISION INSTALLATION

Before fixing the Mattress Base to the bed, please follow the television installation instructions .below

Raise the TV Lift by pressing the TOP button of the remote control.

the main h 

p

Connect TV to the mounting bracket  as shown is Step 8 or 9.

If necessary mounting plate can easily be adjusted to move TV up or down.

Connect the TV Power Lead (supplied with TV) by passing plug down one of the ducts, plugging it into the adapter 

if fitted, 

then into the TV power socket which is on the face of footboard - see Step 

11

. This socket is only to be used for the TV. 

Connect the Aerial & HDMI cable (H&J) by passing down the appropriate duct - see Step 

7.

If required, connect your own media cables through either of the ducts - connect your media equipment when ready.  

Please use the cable clips & cable ties to make certain there are no loose wires to snag or get trapped

.

The TV can now be operated following the TV Operation Guide supplied with your TV.

When finished viewing, lower the TV back into the footboard by pressing DOWN button of the remote control. 

The  TV will retract into the footboard automatically - power shall be turned off when TV reaches the bottom.

When the UP button is pressed - the TV Lifting Column rises and power to the TV turns back on automatically.

TROUBLE SHOOTING

If your equipment does not operate please check all the power connections, to the wall and to the socket in the footboard. 

Make sure TV is switched on. (Note: TV will only work when it is in the up position). 

If the television or TV Lift still fails to operate contact your retailer.

IMPORTANT: Care  should  be  taken  when  connecting  electrical  items.   If

 

in

 

any

 

doubt

 

please consult an approved 

electrician to advise you on the  electrical  supply to achieve safe connections, to the electrical equipment of the TV Bed. 

Summary of Contents for ESTON OTTOMAN TV BED





















Reviews: