Tuxedo LR-26-PAD Assembly & Operation Instruction Manual Download Page 5

1905 N Main St Suite C, Cleburne, TX 76033 
 Ph 817-558-9337              Fax 817-558-9740

TUXEDO DISTRIBUTORS LIMITED WARRANTY 

Structural Warranty: 

The following parts and structural components carry a five year warranty: 

Columns 

Top Rail Beam 

Uprights  

  Arms Swivel  Pins  

Legs 

Carriages         

   Tracks Overhead Beam Cross Rails    

Limited One-Year Warranty: 

Tuxedo Distributors, LLC (“Tuxedo”) offers a limited one-year warranty to the original purchaser of 
Tuxedo lifts and Wheel Service in the United States and Canada. Tuxedo will replace, without charge, any 
part found defective in materials or workmanship under normal use, for a period of one year after purchase.

 

The purchaser is responsible for all shipping charges. This warranty does not apply to equipment that has 
been improperly installed or altered or that has not been operated or maintained according to specifications. 

Other Limitations: 

This warranty does not cover: 

1.

Parts needed for normal maintenance

2.

Wear parts, including but not limited to cables, slider blocks, chains, rubber pads and pulleys

3.

Replacement of lift and tire changer cylinders after the first 30 days. A seal kit and installation
instructions will be sent for repairs thereafter.

4.

On-site labor

Upon receipt, the customer must visually inspect the equipment for any potential freight damage before 
signing clear on the shipping receipt. Freight damage is not considered a warranty issue and therefore must 
be noted for any potential recovery with the shipping company.  

The customer is required to notify Tuxedo of any missing parts within 72 hours. Timely notification must 
be received to be covered under warranty.  

Tuxedo will replace any defective part under warranty at no charge as soon as such parts become available 
from the manufacturer. No guarantee is given as to the immediate availability of replacement parts.  

Tuxedo reserves the right to make improvements and/or design changes to its lifts without any obligation 
to previously sold, assembled or fabricated equipment. 

There is no other express warranty on the Tuxedo lifts and this warranty is exclusive of and in lieu of all 
other warranties, expressed or implied, including all warranties of merchantability and fitness for a 
particular purpose. 

To the fullest extent allowed by law, Tuxedo shall not be liable for loss of use, cost of cover, lost profits, 
inconvenience, lost time, commercial loss or other incidental or consequential damages. 

This Limited Warranty is granted to the original purchaser only and is not transferable or 
assignable. 

Some states do not allow exclusion or limitation of consequential damages or how long an 
implied warranty lasts, so the above limitations and exclusions may not apply. This warranty 
gives you specific legal rights and you may have other rights, which may vary from state to state. 

Summary of Contents for LR-26-PAD














Reviews: