Tuthill KINNEY KSVB 100 Installation Operation Maintenance Repair Manual Download Page 22

WARRANTY – VACUUM PRODUCTS

 

Subject to the terms and conditions hereinafter set forth and set forth in General Terms of Sale, Tuthill Vacuum & Blower 

Systems (the seller) warrants products and parts of its manufacture, when shipped, and its work (including installation and 

start-up) when performed, will be of good quality and will be free from defects in material and workmanship. This warranty 

applies only to Seller’s equipment, under use and service in accordance with seller’s written instructions, recommendations 

and ratings for installation, operating, maintenance and service of products, for a period as stated in the table below. Because 

of varying conditions of installation and operation, all guarantees of performance are subject to plus or minus 5% variation. 

(Non-standard materials are subject to a plus or minus 10% variation).

THIS WARRANTY EXTENDS ONLY TO BUYER AND/OR ORIGINAL END USER, AND IN NO EVENT SHALL THE 

SELLER BE LIABLE FOR PROPERTY DAMAGE SUSTAINED BY A PERSON DESIGNATED BY THE LAW OF ANY 

JURISDICTION AS A THIRD PARTY BENEFICIARY OF THIS WARRANTY OR ANY OTHER WARRANTY HELD TO 

SURVIVE SELLER’S DISCLAIMER.

Product Type

Warranty Duration

New

15 months after date of shipment or 12 months after initial startup date, whichever occurs first

Repair

6 months after date of shipment or remaining warranty period, whichever is greater

Remanufactured

9 months after date of shipment or 6 months after initial startup date, whichever occurs first

All accessories furnished by Seller but manufactured by others bear only that manufacturer’s standard warranty.

All claims for defective products, parts, or work under this warranty must be made in writing immediately upon discovery 

and, in any event within one (1) year from date of shipment of the applicable item and all claims for defective work must 

be made in writing immediately upon discovery and in any event within one (1) year from date of completion thereof by 

Seller. Unless done with prior written consent of Seller, any repairs, alterations or disassembly of Seller’s equipment 

shall void warranty. Installation and transportation costs are not included and defective items must be held for Seller’s 

inspection and returned to Seller’s Ex-works point upon request.

THERE ARE NO WARRANTIES, EXPRESSED, IMPLIED OR STATUTORY WHICH EXTEND BEYOND THE 

DESCRIPTION ON THE FACE HEREOF, INCLUDING WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF 

MERCHANTABILITY AND FITNESS OF PURPOSE.

After Buyer’s submission of a claim as provided above and its approval, Seller shall at its option either repair or replace 

its product, part, or work at the original Ex-works point of shipment, or refund an equitable portion of the purchase price.

The products and parts sold hereunder are not warranted for operation with erosive or corrosive material or those 

which may lead to build up of material within the product supplied, nor those which are incompatible with the materials 

of construction. The Buyer shall have no claim whatsoever and no product or part shall be deemed to be defective by 

reason of failure to resist erosive or corrosive action nor for problems resulting from build-up of material within the unit 

nor for problems due to incompatibility with the materials of construction.

Any improper use, operation beyond capacity, substitution of parts not approved by Seller, or any alteration or repair 

by others in such manner as in Seller’s judgment affects the product materially and adversely shall void this warranty.

No employee or representative of Seller other than an Officer of the Company is authorized to change this warranty in 

any way or grant any other warranty. Any such change by an Officer of the Company must be in writing.

The foregoing is Seller’s only obligation and Buyer’s only remedy for breach of warranty, and except for gross negligence, 

willful misconduct and remedies permitted under the General Terms of Sale in the sections on CONTRACT PERFORMANCE, 

INSPECTION AND ACCEPTANCE and the PATENTS Clause hereof, the foregoing is BUYER’S ONLY REMEDY HEREUNDER 

BY WAY OF BREACH OF CONTRACT, TORT OR OTHERWISE, WITHOUT REGARD TO WHETHER ANY DEFECT WAS 

DISCOVERED OR LATENT AT THE TIME OF DELIVERY OF THE PRODUCT OR WORK. In no event shall Buyer be entitled 

to incidental or consequential damages. Any action for breach of this agreement must commence within one (1) year after the 

cause of action has occurred.

December, 2007

22

Summary of Contents for KINNEY KSVB 100

























Reviews: