background image

 

Aqua

Flash U

ser’s Manual 

14 

5  Warranty

 

 

5.1 Terms 

Turner Designs warrants the

 Aqua

Flash Handheld Active Fluorometer and accessories to 

be free from defects in materials and workmanship under normal use and service for a 
period of 12 months from the date of shipment from Turner Designs, with the following 
restrictions:

 

 

  Turner Designs is not responsible for replacing parts damaged by accident or neglect.  

Damage from corrosion is not covered.  Damage caused by customer modification of the 
instrument is not covered.

 

 

  This warranty covers only Turner Designs products and is not extended to equipment 

used with our products.  We are not responsible for incidental or consequential 
damages, except in those states where this limitation is not allowed.  This warranty gives 
you specific legal rights and you may have other rights which vary from state to state.

 

 

  Damage incurred in shipping is not covered.

 

 

5.2 Warranty Service 
 

To obtain service during the warranty period, the owner shall take the following steps:  

 

1  Write, email, or call the Turner Designs Technical Support department and describe as 

precisely as possible the nature of the problem. 

 

Phone

: 1 (877) 316-8049 

Email

[email protected]

 

 

2  Carry out any adjustments or tests as suggested by the Technical Support Department. 

 

3  If proper performance is not obtained you will be issued a Return Authorization number 

(RMA).  Package the unit, write the RMA number on the outside of the shipping carton, 
and ship the instrument, prepaid, to Turner Designs.  If the failure is covered under the 
warranty terms, the instrument will be repaired and returned free of charge, for all 
customers in the contiguous continental United States. 

 

For customers outside of the contiguous continental United States who purchased 
equipment from one of our authorized distributors, contact the distributor.  If you 
purchased directly, contact us.  We will repair the instrument at no charge.  Customer 
pays for shipping duties and documentation to Turner Designs.  Turner Designs pays for 
return shipment.  Custom duties, taxes and fees are the responsibility of the customer. 

 

5.3

 

Out-of-Warranty Service 
Follow steps for Warranty Service as listed above.  If our Technical Support department can 
assist you by phone or correspondence, we will be glad to, at no charge.  Repair service will 
be billed on a fixed price basis, plus any applicable duties and/or taxes.  Shipment to Turner 
Designs should be prepaid.  Your bill will include return shipment freight charges. 

 

Address for Shipment: 

Turner Designs 

845 W. Maude Avenue 

Sunnyvale, CA 94085

 

 

Summary of Contents for AquaFlash



















Reviews: