background image

8

Figure 16

Figure 17

11. OPERATING 

INSTRUCTIONS

Restore power to ceiling fan and test for proper 
operation.

A.   

HI, MED,

 and 

LOW

 buttons:

       These three buttons are used to set   the fan 
       speed as follows:
            HI= high speed
            Med= medium speed
            Low= low speed

B.   

OFF

 button:

       This button turns the fan off.

C.  

LIGHT

 button:   

This button controls the light. Press and release the 
button to turn the light ON or OFF. Press and hold 
the button to set the desired brightness. The light 
key has an auto-resume, it will stay at the same 
brightness as the last time it was turned off.
                                 
The Reverse switch is located on the top of the 
motor housing. Reverse the switch to the Left for 
warm weather operation. Slide the switch to the 
Right  for cool weather operation.

Speed  settings  for  warm or cool weather depend 
on factors such as the room size. Ceiling height, 
number of fans and so on.

NOTE:

 Wait  for  fan  to  stop  before  changing  the 

setting of the slide switch.

10.  INSTALLING THE  
       BATTERY

Install 9 volt battery (included), to prevent damage 
to transmitter, remove the battery if not used for 
long periods. (Fig. 16) 

9 Volt Battery  

LOW

OFF

HI

MED

Summary of Contents for Elise













Reviews: