background image

22

Milan Series

FEDERAL COMMUNICATIONS 
COMMISSION COMPLIANCE 
INFORMATION

Responsible Party Name: 

MUSIC Group Services US Inc.

Address: 

18912 North Creek Parkway,
Suite 200 Bothell, WA 98011, USA

Phone Number: 

+1 425 672 0816

MILAN M18B/M15B/M15/M12/M10

complies with the FCC rules as mentioned in the 
following paragraph:

This equipment has been tested and found to comply with 
the limits for a Class B digital device, pursuant to part 15 
of the FCC Rules. These limits are designed to provide 
reasonable protection against harmful interference in a 
residential installation. This equipment generates, uses and 
can radiate radio frequency energy and, if not installed and 
used in accordance with the instructions, may cause harmful 
interference to radio communications. However, there is 
no guarantee that interference will not occur in a particular 
installation. If this equipment does cause harmful interference 
to radio or television reception, which can be determined by 
turning the equipment off and on, the user is encouraged 
to try to correct the interference by one or more of the 
following measures:

• 

• 

Reorient or relocate the receiving antenna

• 

• 

Increase the separation between the equipment and receiver

• 

• 

Connect the equipment into an outlet on a circuit different 
from that to which the receiver is connected

• 

• 

Consult the dealer or an experienced radio/TV technician 
for help

This device complies with Part 15 of the FCC rules. Operation is 
subject to the following two conditions:

(1) this device may not cause harmful interference, and 
(2) this device must accept any interference received, including 
interference that may cause undesired operation.

Important information:

Changes or modifi cations to the equipment not expressly 
approved by MUSIC Group can void the user’s authority to 
use the equipment.

TURBOSOUND

MILAN M18B/M15B/M15/M12/M10

Summary of Contents for Milan M10

























Reviews: