background image

5

USER MANUAL

TUNJKBTL30L

5.  OPERATING INSTRUCTIONS

WARNING! Ensure that you read, understand and apply the safety instructions and warnings before use.

Lifting

 •

Turn the handle/release valve clockwise to the closed position. Do not over tighten.

 •

Position the jack under the specified lift point.

 •

Begin lifting by pumping the handle up and down.

 •

Immediately after lifting, support the vehicle with appropriately rated axle stands.

 •

Turn the handle/release valve slowly counterclockwise to lower the vehicle onto axle stands.

Lowering

• 

Turn the handle/release valve clockwise to the closed position. Do not over tighten.

• 

Pump the handle up and down to lift vehicle off axle stands.

• 

Remove the axle stands. Do not get under or let anyone get under the vehicle while lowering.

• 

Turn the handle/release valve slowly counterclockwise to lower the vehicle onto the ground.

6.  TROUBLESHOOTING

Symptom

Possible Causes

Solution

Jack will not lift the load

1. Release valve not tightly closed

2. Low oil level

3. Defective or worn internal parts

4. Load exceeds maximum allowance

1. Tighten release valve

2. Check and add oil. Follow "Check and Refill Oil" 

instructions on facing page

3. Discontinue use and contact a local repair centre

4. Use a higher capacity jack

Jack will not hold the load

1. Release valve not tightly closed

2. Power unit malfunction

1. Tighten release valve

2. Discontinue use and contact a local repair centre

Jack will not descend to 

minimum height, or will not 

remain in lowered position

1. Air trapped in system

2. Reservoir oil overfilled

1. Vent air out of system. Follow "Air Venting 

Procedures" on facing page

2. Check and ensure proper oil level. Follow "Check and 

Refill Oil" instructions on facing page

Jack will not lift to  

maximum height

1. Low oil level

1. Check and ensure proper oil level. Follow "Check and 

Refill Oil" instructions on facing page

Jack will not function 

properly after trying 

solutions listed above

1. Internal malfunction or structural 

damage

1. Stop usage and contact an authorised repair centre

30 TONNE

 

BOTTLE JACK

  

USER MANUAL

TUNJKBTL30L

Summary of Contents for UNJKBTL30L













Reviews: