background image

 

 

 
 

FAILURE TO HEED THE FOLLOWING WARNINGS 

MAY RESULT IN SERIOUS INJURY OR DEATH! 

 
 

 

Do not use to lift or move people. If your task involves 
moving or lifting people, you must use the proper 
equipment, not this winch. 

 

 

Winch operators must be trained in the proper, safe 
operation of the winch. 

 

 

Cable anchors on Tulsa Winches are not designed to 
hold the rated load of the winch. You must keep at least 
five (5) wraps of cable on the drum to insure that the 
cable doesn’t come loose. 

 

 

Stay clear of suspended loads and of cable under 
tension. A broken cable or dropped load can cause 
serious injury or death. 

 

 

Make sure that all equipment, including the winch and 
cable, is maintained properly. Pay especially close 
attention to the clutch, making sure that it fully engages 
when shifted. Do not attempt to disengage the clutch 
when a load is on the winch. 

 

 

Avoid shock loads. This type of load imposes a strain 
on the winch many times the actual weight of the load 
and can cause failure of the cable or of the winch. 

 

 

 
 

WARNING 

Summary of Contents for Rufnek Intelliguard 1200W

















Reviews: