manualshive.com logo in svg

TSC TTP-286MT Series, User Manual

Share
Download
TSC TTP-286MT Series User Manual Download Page 53

- 46 - 

 

6.3 Setting Ethernet by Diagnostic Tool 

 

The Diagnostic Utility is enclosed in the CD disk \Utilities directory. Users can use Diagnostic Tool to 

setup the Ethernet by RS-232, USB and Ethernet interfaces. The following contents will instruct users 

how to configure the Ethernet by these three interfaces. 

 

6.3.1 Using USB interface to setup Ethernet interface 

 

1.  Connect the printer and computer with USB cable. 

2.  Turn on the printer power switch. 

3.  Start the Diagnostic Utility by double clicking on the                 

icon.

 

4.  The Diagnostic Utility default interface setting is USB interface. If USB interface is connected with 

printer, no other settings need to be changed in the interface field.

 

 

5.  Click on the 

“Ethernet Setup” button from “Printer Function” group in Printer Configuration tab to 

setup the IP address, subnet mask and gateway for the on board Ethernet.

 

  

 

 

 

 

 

Summary of Contents for TTP-286MT Series
































































Reviews:

No comments

Brands by name

Popular brands

Load more brands