TSC TTP-244CE series Service Manual Download Page 30

Page: 30 / 33

TTP-245C/ TTP-343C/ TTP-244CE
Bar Code Printer Service Manual

Sensor

Compressed air or vacuum

Monthly

Exterior

Wipe it with water-dampened

cloth

As needed

Interior

Brush or vacuum

As needed

Note:



Do not touch printer head by hand. If you touch it careless, please use ethanol to

clean it.



Please use 100% Ethenol. DO NOT use medical alcohol, which may damage the

printer head.



Regularly clean the print head and supply sensors once change a new ribbon to

keep printer performance and extend printer life.



Continuous printing will cause printer motor overheat. Printer will stop printing

automatically about 10~15 minutes until motor is cooling down. Please don't turn off

power when printer pauses or the data transfered to printer buffer will be lost.



The maximum printing ratio per dot line is 15% for this printer. To print the full web

black line, the maximum black line height is limited to 40 dots, which is 5mm for 203

DPI resolution printer and 3.3mm for 300 DPI resolution printer.

Summary of Contents for TTP-244CE series


































Search results

Summary of Contents for TTP-244CE series

Reviews:

Related manuals for TTP-244CE series

Brands by name

Popular brands

TSC TTP-244CE series, Service Manual

Search results

Summary of Contents for TTP-244CE series

Reviews:

Related manuals for TTP-244CE series

Brands by name

Popular brands