background image

 

 

 

 

End Product Labeling 

 
This transmitter module is authorized only for use in device where the antenna may be 
installed such that 20cm may be maintained between the antenna and users. The final 
end product must be labeled in a visible area with the following: "Contains FCC ID: VTV-RF-
WKD ” and "Contains IC: 10524A-RF-WKD “ 
 

Information for the OEMs and Integrators 

 
The following statement must be included with all versions of this document supplied to an 
OEM or integrator, but should not be distributed to the end user. 
 
1) This device is intended for OEM integrators only. 
2) Please see the full Grant of Equipment document for other restrictions. 

 

 

This radio transmitter FCC ID: VTV-RF-WKD has been approved by FCC to operate with 
the antenna types listed below with the maximum permissible gain and required antenna 
impedance for each antenna type indicated. Antenna types not included in this list, having a 
gain greater than the maximum gain indicated for that type, are strictly prohibited for use 
with this device. 
 

Antenna List 

No. Manufacturer 

Part No. 

Antenna Type 

Peak Gain 

1 ARISTOTLE 

ENTERPRISES INC. 

RFA-25-P393B-70-85-L FPC 

3.2 dBi for 2.4 GHz 
3.1 dBi for 5 GHz 

2 ARISTOTLE 

ENTERPRISES INC. 

RFA-25-P393B-70B140R

 

FPC 

0.9 dBi for 2.4 GHz 
3.2 dBi for 5 GHz 

Note: The antenna connector is I-PEX type. 

 

Canada, Industry Canada (IC) Notices 

 
This device complies with Canada licence-exempt RSS standard(s).  
Operation is subject to the following two conditions: (1) this device may not cause 
interference, and (2) this device must accept any interference, including interference that 
may cause undesired operation of the device. 
 

Canada, avis d'Industry Canada (IC) 

 
Cet appareil est conforme avec Industrie Canada exemptes de licence RSS standard(s).  
Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit 
pas causer d'interférence et (2) cet appareil doit accepter toute interférence, notamment les 
interférences qui peuvent affecter son fonctionnement. 

 

 
This device is slave equipment, the device is not radar detection and not ad-hoc operation in 
the DFS band. 

Summary of Contents for RF-WKD




















Reviews: