background image

 

 

62 

9. Angency Complicance and Approvals 

 

 

EN 55032, Class A 
EN 55035 
EN 60950-1 
This is a class A product. In a domestic environment this product may cause radio interference in which case the user 

may be required to take adequate measures.

 

 

FCC part 15B, Class A 
ICES-003, Class A 
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 

of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the 
equipment is operated in a commercial environment. 

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance 

with the manufacturer’s instruction manual, may cause harmful interference with radio communications. Operation of 
this equipment in a residential area is likely to cause harmful interference, in which case you will be required to 
correct the interference at your own expense. 

This Class A digital apparatus complies with Canadian ICES-003. 
Cet appareil numérique de la classe A est conform à la norme NMB-003 du Canada.             
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This 

device may cause harmful interference, and (2) this device must accept any interference received, including 
interference that may cause undesired operation.

 

Summary of Contents for PRINTRONIX ML240 Series














































































Reviews: