manualshive.com logo in svg

Trueshopping 110CB2400, Instruction Manual

Share
Download
Trueshopping 110CB2400 Instruction Manual Download Page 22

Trueshopping

Turbo nozzle

 

(Not included with all models)

A turbo nozzle, sometimes referred to as a rotary nozzle, 
is a very effective tool that can significantly reduce 
cleaning time. The turbo nozzle combines the power of a 
narrow high impact stream and the efficiency of a 25 
degree fan pattern. This swirls the narrow high impact 
stream into a cone shape that cleans a larger area.

CAUTION:

 Since a turbo nozzle uses a narrow high 

impact stream, only use it in applications where the 
cleaning surface cannot be damaged by narrow high 
impact spray. Additionally, the turbo nozzle is not 
adjustable and cannot be used to apply detergent. 

Adjustable spray nozzle

Turn off the spray lance first, hold the rear part of spray 
nozzle, then turn the front part of spray nozzle clockwise. 
Water may be sprayed out from the spray nozzle in fan 
shapes (fig 1); turn the front part of spray nozzle 
withershins, water may be sprayed out from the spray 
nozzle linearly (fig 2).

Summary of Contents for 110CB2400



































Reviews:

No comments

Brands by name

Popular brands

Load more brands