background image

Chef Base Series

www.truemfg.com

TEC_TM_159 | REV. A | EN

07/6/2022 

Page 8 of 19

Installation (cont.)

Leveling

Proper leveling of your TRUE cooler is critical to operating success 
(for non-mobile models). Leveling impacts effective condensate 
removal and door operation.

Procedure

Level the unit front-to-back and side-to-side.

1. 

Position the level on the inside floor of the unit near the doors 
(the level should be parallel to cabinet front). Level the cabinet.

2. 

Position the level at the inside rear of cabinet (again, the level 
should be placed parallel to cabinet back). Level the cabinet.

3. 

Perform procedures similar to steps 1 and 2 by placing the 
level on inside floor (left and right side, parallel to the depth of 
the cooler). Level the cabinet.

NOTE: If the cabinet has a center leveling screw, castor, or leg, 

make sure it is adjusted properly so it makes full contact with 

the floor after the cabinet has been leveled.

Sealing the Cabinet to the Floor

Asphalt floors are susceptible to chemical attack. A layer of tape 
may be placed on the floor prior to applying the sealant to protect 
the floor.

Procedure

1. 

Position the cabinet, allowing 3" (73 mm) between the wall 
and the rear of the cabinet to ensure proper ventilation.

2. 

Level the cabinet. The cabinet should be level side-to-side 
and front-to-back. To check that the cabinet is level, place a 
carpenter's level on the interior cabinet floor in four places:

a. 

Position the level on the inside floor of the cabinet, near 

the doors (the level should be placed parallel to the cabinet 
front). Level the cabinet.

b. 

Position the level at the inside rear of the cabinet (the level 

should be placed parallel to the cabinet back). Level the 
cabinet.

c. 

Perform procedures similar to a and b by placing the level 

on the left and right inside floor (level should be parallel to 
the cabinet sides). Level the cabinet.

3. 

Draw an outline of the cooler base on the floor.

4. 

Raise and block the front side of the cabinet.

5. 

Apply a bead of NSF-approved sealant (see list below) to the 
floor, 1/2" (13 mm) inside the front part of the outline drawn in 
step 4. The bead of sealant must be heavy enough to seal the 
entire cabinet surface when the cabinet is lowered on top of 
the sealant.

6. 

Raise and block the rear of the cabinet.

7. 

Apply sealant to the floor on the other three sides, as outlined 
in step 5.

8. 

Examine the the cabinet to ensure that it is sealed to the floor 
around the entire perimeter.

NSF-Approved Sealants

•  3M #ECU800 Caulk
•  3M #ECU2185 Caulk
•  3M #ECU1055 Bead
•  3M #ECU1202 Bead
•  Armstrong Cork – Rubber Caulk
•  Products Research Co. #5000 Rubber Caulk
•  G.E. Silicone Sealer
•  Dow Corning Silicone Sealer

 A

 B

C

Fig. 4. 

Install castor shims in pairs.

Snug Fit

Here

Castor

Mounting

Plate

Castor

Leveling Shims

Leveling Shims

Side View

Left

Shim in

Position

Top View

Summary of Contents for TRCB Series




















Reviews: