True Manufacturing Company TCGR-50 Installation Manual Download Page 15

............ www.truemfg.com ............

True Food Service Equipment, Inc.

13

13

MAINTENANCE, CARE & CLEANING

•  The exterior may be wiped clean with mild soap 

and water.  The use of stainless steel cleaners 
or other such solvents is not recommended on 
plastic parts.  Warm soap and water will suffice.

CAUTION:  Do not use any steel wool, abrasive or 
chlorine based products to clean stainless steel sur-
faces.

  The interior of the display case should be cleaned 

periodically and we recommend a mild solution 
of diluted baking soda and water which will help 
reduce any inherent odors.  Do not use harsh 
cleaners on any surface of the interior.

CABINET CLEANING

It may be necessary to seal the bakery case to the 
floor for local sanitary codes or if the customer so 
desires.  TRUE recommends either of the following 
methods.

A.

   Using a vinyl cove base trim as produced by 

Armstrong

Johnson

, or 

Kentile

 (available at floor 

covering suppliers) or 

    Using mastics available at hardware stores.

B.  

When applying the cove base trim, thoroughly 
clean both the cabinet and floor of dirt and 
grease.  Apply a recommended contact cement 
to the cove base trim.  After cove base trim has 
dried, fill in cracks and joints with a caulking 

material.

C.

   When applying a mastic, thoroughly clean both 

the cabinet and floor of dirt and grease.  Draw 
an outline of the cabinet on the floor.  Raise 
and block the front side of the cabinet.  Apply a 
bead of mastic to the floor 

1

/

2

" (1.3 cm) inside 

the outline drawn.  Lower the cabinet.  Raise 
and block the rear side of the cabinet.  Apply the 
bead of mastic, lower the cabinet.

OPTIONAL 

(SEALING CABINET TO FLOOR)

Summary of Contents for TCGR-50























Reviews: