background image

............ www.truemfg.com ............

True Food Service Equipment, Inc.

14

14

MAINTENANCE, CARE & CLEANING

LIGHT BULB REPLACEMENT

SHELF MOUNTED BULB REPLACEMENT:
WARNING

When replacing a light bulb make sure power to the unit 

is either turned off or unplugged.

A.

  Unplug the light assembly from the receptacle 

on the interior side wall. Remove shelf and light 

assembly from cabinet. 

B.

  Remove the lampshield by gently squeezing the 

sides together and rotating out (image 1).

C.

  Remove bulb from the corded end of assembly 

by holding the bulb and gently pulling up on 

spring loaded lampholder which will allow enough 

clearance to remove bulb (image 2).

NOTE

All spring loaded lampholders are located on the left side 

of the cabinet as you face the front.

NOTE

Please be aware of your local ordinances for disposal of 

old florescent bulbs. These bulbs should be disposed of in 

a safe and proper manner.

D.

  Install new bulb using spring loaded lampholder.

E.

   Reinstall light assembly and shelf. Plug cord into 

side wall receptacle.

INTERIOR TOP BULB REPLACEMENT:
WARNING

When replacing a light bulb make sure power to the unit 

is either turned off or unplugged.

A.

  Remove the lampshield by gently squeezing the 

sides together and rotating out (image 3).

B.

  Remove bulb by gently pushing bulb back into 

spring loaded lampholder which will allow enough 

clearance to remove bulb (image 4).

C.

  Install new bulb using spring loaded lampholder.

D.

  Reinstall light lampshield by sliding rear "U" 

channel of lampshield over metal bracket and 

gently squeezing lampshield to fit front "U" 

channel over front metal bracket (images 5-6).

E.  

Image 7 shows assembly properly installed.

Squeeze lampshield and 
rotate out.

Remove bulb by gen-
tly pulling up on spring 
loaded lampholder.

Squeeze lampshield and 
rotate out.

Remove bulb by gently pushing 
bulb into spring loaded lam-
pholder.

Squeeze lampshield "U" 
channel into position over 
metal bracket.

lampshield "U" channel 
in position over metal 
bracket.

Interior top light assembly 
properly installed.

1

2

3

5

6

7

4

Summary of Contents for TCGDZ-50






















Reviews: