True Manufacturing Company T-23DF-HC Installation Manual Download Page 3

2

TRUE

T-23DF-HC

www

.

truemfg

.

com

RISK OF CHILD 
ENTRAPMENT

PROPER DISPOSAL OF THE REFRIGERATOR

Child entrapment and suffocation are not problems of the past. 
Junked or abandoned refrigerators are still dangerous… even if they 
will sit for “just a few days.” If you are getting rid of your old refrigera-
tor, please follow the instructions below to help prevent accidents.

BEFORE YOU THROW AWAY YOUR  OLD 
REFRIGERATOR OR FREEZER: 

•  Take off the doors.
•  Leave the shelves in place so that children may not easily climb 

inside.

APPLIANCE DISPOSAL

When recycling appliance please make sure that the refrigerants are 
handled according to local and national codes, requirements and 
regulations.

REFRIGERANT DISPOSAL

Your old refrigerator may have a cooling system that uses “Ozone 
Depleting” chemicals. If you are throwing away your old refrigerator, 
make sure the refrigerant is removed for proper disposal by a quali-
fied service technician. If you intentionally release any refrigerants you 
can be subject to fines and imprisonment under provisions of the 
environmental regulations.

USE OF EXTENSION CORDS

NEVER USE AN EXTENSION CORD! 

 TRUE will not war-

ranty any refrigerator that has been connected to an extension cord.

REPLACEMENT PARTS

•  Component parts shall be replaced with like components.
•  Servicing shall be done by authorized service personnel, to 

minimize the risk of possible ignition due to incorrect parts or 
improper service.

•  Lamps must be replaced by identical lamps only.
•  If the supply cord is damaged, it must be replaced by a special 

cord or assembly available from the manufacturer or its service 
agent.

HOW TO CONNECT ELECTRICITY

DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR 
REMOVE THE GROUND PRONG FROM THE POWER 
CORD. FOR PERSONAL SAFETY, THIS APPLIANCE 
MUST BE PROPERLY GROUNDED. 

The power cord from this appliance is equipped with a grounding 
plug which minimizes the possibility of electric shock hazard.

Have the wall outlet and circuit checked by a qualified electrician to 
make sure the outlet is properly grounded.

If the outlet is a standard 2-prong outlet, it is your personal respon-
sibility and obligation to have it replaced with the properly grounded 
wall outlet.

The refrigerator should always be plugged into it’s own individual 
electrical circuit, which has a voltage rating that matches the rating 
plate.

This provides the best performance and also prevents overloading 
building wiring circuits which could cause a fire hazard from over-
heated wires.

Never unplug your refrigerator by pulling on the power cord. Always 
grip plug firmly and pull straight out from the outlet.

Repair or replace immediately all power cords that have become 
frayed or otherwise damaged. Do not use a cord that shows cracks 
or abrasion damage along its length or at either end.

When removing the refrigerator away from the wall, be careful not 
to roll over or damage the power cord.

If supply power cord is damaged it should be replaced with original 
equipment manufacture parts.  To avoid hazard this should be done 
by a qualified service technician.

USE OF ADAPTER PLUGS

NEVER USE AN ADAPTER PLUG! 

Because of potential safety 

hazards under certain conditions, we strongly recommend against the 
use of an adapter plug.

The incoming power source to the cabinet including any adapters 
used must have the adequate power available and must be properly 
grounded.  Only adapters listed with UL should be used.

NORTH AMERICA USE ONLY!

NEMA plugs

TRUE uses these types of plugs. If you do not have the right outlet 
have a certified electrician install the correct power source. 

NOTE:

  

International plug configurations vary by voltage and country.

115/60/1

NEMA-5-15R

115/208-230/1

NEMA-14-20R

115/60/1

NEMA-5-20R

208-230/60/1

NEMA-6-15R

WARNING!

DANGER!

Summary of Contents for T-23DF-HC























Reviews: