Truck Hero extang XCEED Installation Sheet Download Page 4

IMPORTANT 

IMPORTANT NOTICE

Bed cover safe operation and use 

While driving, the cover must be completely at and secure with all latches  

in the closed position OR completely folded up (all panels) and secured at  

the cab. DO NOT DRIVE with cover partially opened. 

Tonneau Cover Positions While Operating Vehicle

Tail Panel Operation

Prior to vehicle operation, the bed cover MUST be properly secured.  

CLOSED POSITION

To close the tailgate panel

To open the tailgate panel

All panels must be at, closed and FULLY LATCHED to the bed cover side rail.

FOLDED & SECURED FLAT AT FRONT OF BED

FOLDED POSITION

FOLDED & PROPPED UP TO CAB

FOLDED & PROPPED UP POSITION

Fold the cover open and lift it until it is vertical, or 90 degrees.  
Release the prop rods from the rail clips and engage the 
end of the prop rod with the ball tting of the cover bracket.  
Always engage both sides.

Your cover should be rmly in
position with little to no movement
once the prop rods are locked.

Strap Storage 

Position

The tailgate can be closed with the cover either 
up or down.

Open the tailgate and reach under the driver’s 
side of the tail panel for the rotary handle.
Rotate the handle to release both latches, lift
the panel to open.

To drive with your bed cover in the folded position, use the tie 
down straps and buckles provided with your cover.  Ensure that 
BOTH buckle clips are fully inserted into the buckle ends located 
on the front header panel of the cover, and adjust the straps to 
ensure the cover is secure during vehicle operation.  The clips should 
be secured in the storage position, as shown in Figure1, 
when the straps are not in use.

Figure 1

DO NOT DRIVE WITH THE TONNEAU 
IN A PARTIALLY OPEN POSITION!

Additional Important Operating Tips

The bed cover MUST be free of foreign material including snow 

and ice before opening the panels.

Do Not 

tow your vehicle from the rear with the bed cover in place.

Do Not

 operate the vehicle with objects on top of the cover.

FAILURE TO FOLLOW THESE CAUTIONS MAY RESULT IN SEVERE DAMAGE TO THE COVER
AND WILL VOID YOUR WARRANTY!

Remove any snow or 
foreign matter before 
folding the cover.

Do Not tow your vehicle
from the rear with the 
cover on the truck.

Summary of Contents for extang XCEED







Reviews: