background image

12

MAINTENANCE

WARNING:

 To avoid serious personal injury, always stop 

the engine and allow it to cool before cleaning or maintaining 

the unit. Never perform cleaning or maintenance while the 

unit is running. Disconnect the spark plug wire to prevent 

the unit from starting accidentally.

WARNING:

 Wear protective clothing and observe all 

safety instructions to prevent serious personal injury.

MAINTENANCE SCHEDULE 

Perform these required maintenance procedures at the frequency 

stated in the table. These procedures should also be a part of any 

seasonal tune-up. 
NOTE: Some maintenance procedures may require special tools or 

skills. If you are unsure about these procedures, take the unit to 

an MTD authorized service dealer. 

NOTE: Maintenance, replacement, or repair of the emission control 

devices and system may be performed by an MTD authorized 

service dealer. 

NOTE: Please read the California/EPA statement that came with the 

unit for a complete listing of terms and coverage for the emissions 

control devices, such as the spark arrestor, muffler, carburetor, etc.

FREQUENCY

MAINTENANCE REQUIRED

Every 10 hours

• Clean and re-oil the air filter. Refer to 

Maintaining the Air Filter.

After the first 

10 hours and 

at 38 hours

• Change the oil. Refer to Changing the Oil
• Have the rocker arm clearance checked by 

an authorized service dealer. 

• Check the spark plug condition and gap. 

Refer to Maintaining the Spark Plug.

REPLACING THE EDGER BLADE 

Removing the Edger Blade

 

1. Place a 15/16 in. wrench over the lock nut (Fig. 12). 
2. Insert a 5/16 in. Allen wrench into the spindle hole (Fig. 12). 
3. While hold ing the Allen wrench in place, loosen the lock nut by 

turning it counterclock wise with the wrench (Fig. 12).  

4. Remove the Allen wrench, wrench, lock nut and edger blade 

(Fig. 13). Keep the lock nut for installing the new edger blade. 

Installing the Edger Blade 
1. Install the new edger blade and lock nut onto the output shaft 

(Fig. 13). Make sure the blade edges are facing the correct 

direction (Fig. 13). The unit will not function properly if the edger 

blade is facing the wrong direction.  

2. Place the wrench over the lock nut (Fig. 12). 
3. Insert the Allen wrench into the spindle hole (Fig. 12). 
4. While hold ing the Allen wrench in place, tighten the lock nut by 

turning it clock wise with the wrench (Fig. 12). Make sure that the 

edger blade stays flat and centered against the output shaft 

while tightening the lock nut. Tighten the lock nut until the edger 

blade is firmly secure. 

5. Remove the wrench and Allen wrench.

Fig. 12

Spindle Hole

Allen Wrench

Wrench

Fig. 13

Lock Nut

Edger Blade

Blade Edges

Output Shaft

Loosen

Tighten

WARNING:

 Make sure the blade is flat against the 

output shaft bushing after the lock nut is tightened. If the 

blade is off-cen ter, the unit will be dam aged by vibration, 

and the blade may fly off, which can cause serious 

personal in ju ry.

Summary of Contents for TBE304









































Reviews: