4
EN
cordless tacker PTNS 10-20V
•
Keep handles and grasping surfaces dry, clean and
free from oil and grease.
Slippery handles and grasping
surfaces do not allow for safe handling and control of the
tool in unexpected situations.
General Power Tool Safety Warnings – Battery tool
use and care
•
Recharge only with charger specified by the
manufacturer.
A charger that is suitable for one type of
battery pack may create a risk of fire when used with
another battery pack.
•
Use power tools only with specifically designed battery
packs.
Use of any other battery packs may create a risk of
injury and fire.
•
When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys, nails,
screws or other small metal objects, that can make a
connection from one terminal to another.
Shorting the
battery terminals together may cause burns or a fire.
•
Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally
occurs, flush with water. If liquid contacts eyes,
additionally seek medical help.
Liquid ejected from the
battery may cause irritation or burns.
•
Do not use a battery pack or tool that is damaged or
modified.
Damaged or modified batteries may exhibit
unpredictable behaviour resulting in fire, explosion or risk
of injury.
•
Do not expose a battery pack or tool to fire or
excessive temperature.
Exposure to fire or temperature
above 130 °C may cause explosion.
•
Follow all charging instructions and do not charge the
battery pack or tool outside the temperature range
specified in the instructions.
Charging improperly or at
temperatures outsides the specified range may damage
the battery and increase the risk of fire.
General Power Tool Safety Warnings – Service
•
Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will
ensure that the safety of the power tool is maintained.
•
Never service damaged battery pack.
Service of battery
packs should only be performed by the manufacturer or
authorized service providers.
Safety instructions for tackers
•
Always assume that the power tool contains fasteners
(wire nails or staples).
Careless handling of the tacker
can result in an unexpected ejection of wire nails or
staples and lead to personal injury.
•
Do not point the power tool towards yourself or anyone
nearby.
Unexpected triggering will eject a wire nail or
staple which might cause an injury.
•
Do not actuate the power tool until it is placed firmly
against the workpiece.
If the power tool is not in contact
with the workpiece, the staple or wire nail might ricochet.
•
Disconnect the power tool from the mains connection
or battery when a wire nail or staple is jammed inside.
If not de-energized, the tacker could be actuated by
accident while removing a jammed staple or wire nail.
•
Exercise particular caution when removing a jammed
wire nail or staple.
The mechanism may be under tension
and the staple or wire nail could be forcefully ejected while
you attempt to eliminate the jam.
•
Do not use this tacker for fastening electrical lines.
It is
not suitable for the installation of electrical lines, it could
damage the insulation of electric cables thereby causing
electric shock and fire hazards.
•
Use appropriate detection equipment to track down
concealed supply lines or consult the local utility
companies.
Contact with electrical lines may result in fire
and electric shock. Damaging a gas line may lead to an
explosion. Penetrating a water line causes property
damage and may cause an electric shock.
•
Do not under any circumstances use the power tool if
you detect damages on the mains plug or power cable.
If the supply cord is damaged, it must be replaced by the
manufacturer, his service agent or similarly qualified
persons in order to avoid a hazard.
Defective power cables pose a serious health risk!
•
Use clamps or another practical way to secure and
support the workpiece to a stable platform.
Holding the
workpiece by your hand or against the body leaves it
unstable and may lead to loss of control.
Intended use
Only use the device
PTNS 10-20V
for tacking cardboard,
leather, insulating material, fabrics made of textile or natural
fibres, foils and similar materials onto a soft ground such as
softwood or material similar to wood whilst adhering to the
technical data.
We recommend using the power tool with original Trotec
accessories.