background image

EN

6

Operating manual – cordless glue gun PGGS 10-3,7V

Transport and storage

Notice

If you store or transport the device improperly, the
device may be damaged.
Note the information regarding transport and storage of
the device.

Transport

Before

 transporting the device, proceed as follows:

Switch off the device.

Hold onto the mains plug while pulling the power cable of
the charger out of the mains socket.

Allow the device to cool down.

The supplied Li-ion batteries are subjects to the requirements of
dangerous goods legislation.
Observe the following when transporting or shipping Li-ion
batteries:

The user may transport the batteries by road without any
additional requirements.

If transport is carried out by third parties (e.g. air transport
or forwarding company), special requirements as to
packaging and labelling must be observed. This includes
consulting a dangerous goods specialist when preparing
the package.

– Only ship batteries if their housing is undamaged.
– Please also observe any other national regulations.

Storage

Before

 storing the device, proceed as follows:

Switch off the device.

Hold onto the mains plug while pulling the power cable of
the charger out of the mains socket.

Allow the device to cool down.

Clean the device as described in the Maintenance chapter.

Do not store Li-ion batteries which are completely
discharged. Storing discharged batteries can lead to a
deep discharge and thus damage the battery.

When the device is not being used, observe the following
storage conditions:

dry and protected from frost and heat

ambient temperature below 40 °C

protected from dust and direct sunlight.

Start-up

Unpacking the device

Take the device and the accessories out of the packaging.

Warning of electrical voltage

Electric shock from insufficient insulation.
Check the device for damages and proper functioning
before each use.
If you notice damages, no longer use the device.
Do not use the device when the device or your hands
are damp or wet!

Check the scope of delivery for completeness and look for
damages.

Warning

Risk of suffocation!
Do not leave the packaging lying around. Children may
use it as a dangerous toy.

Dispose of the packaging material according to the
national regulations.

Charging the battery

Caution

While the battery is charging, the handle may become
slightly warm. This is normal.

Notice

The battery can be damaged in case of improper
charging.
Never charge the battery at ambient temperatures
below 10 °C or above 40 °C.

The battery is partially charged upon delivery to avoid damage
to the battery caused by a deep discharge.
The battery should be charged prior to initial start-up and when
the battery is low (the battery level indication is illuminated in
red).
To do so, please proceed as follows:

Summary of Contents for PGGS 10-230V















Reviews: