background image

12

EN

compressor PCPS 10-1100

Checking the pressure

1. Connect the compressed-air gun (12) to the compressor

(see chapter Connecting the compressed-air gun).

2. Check whether a valve adapter is required for the planned

activity and, if so, connect it.

3. Connect the compressed-air gun directly to the item to be

inflated by means of the mounted valve adapter.

ð

The current pressure of the connected item will be
indicated on the pressure gauge (10).

Inflating

1. Switch the device on by setting the on/off switch (2) to

position 

I

.

ð

The compressor starts to build up pressure immediately
and is ready for use.

2. Pull and hold the trigger (14) until the desired pressure has

been reached on the pressure gauge (10).

14

3. Switch the device off by setting the on/off switch (2) to

position 

0

.

Deflating

If the existing pressure is too high or if the desired pressure was
exceeded during inflation, the excess air can be released. To do
so, please proceed as follows:

1. Press and hold the deflation valve (11) until the pressure

has been reduced to the desired value displayed on the
pressure gauge (10).

11

2. Disconnect the quick-release lever or any adapter used

from the inflated item.

Shutdown

Warning of electrical voltage

Do not touch the mains plug with wet or damp hands.

Switch the device off.

Hold onto the mains plug while pulling the power cable out
of the mains socket.

If required, allow the device to cool down.

Disconnect any adapters used from the compressed-air
gun (12).

Disconnect the compressed-air gun (12) from the
compressor (see chapter Disconnecting the 
compressed-air gun).

Clean the device according to the Maintenance chapter.

Store the device according to the Storage chapter.

Summary of Contents for PCPC 10-1100

















Reviews: